Gigabyte R282-G30 User Manual Download Page 56

Page: 56 / 109

- 56 -

BIOS Setup

5-2-2 Serial Port Console Redirection

(Note) Advanced items prompt when this item is defined.

Parameter

Description

COM1 Console
Redirection

(Note)

Console redirection enables the users to manage the system from a
remote location.
Options available: Enabled, Disabled. Default setting is

Disabled

COM1 Console Redirection
Settings

Press [Enter] to configure advanced items.

Please note that this item is configurable when COM1 Console

Redirection is set to Enabled.

Terminal Type

– Selects a terminal type to be used for console redirection.

– Options available: VT100, VT100+, VT-UTF8, ANSI. Default setting

VT100+

Bits per second

– Selects the transfer rate for console redirection.

– Options available: 9600, 19200, 38400, 57600, 115200. Default

setting is

115200

Data Bits

– Selects the number of data bits used for console redirection.

– Options available: 7, 8. Default setting is

Summary of Contents for R282-G30














































































































Search results

Summary of Contents for R282-G30

Reviews:

Gigabyte R282-G30, User Manual, Page: 56 / 109

Search results

Summary of Contents for R282-G30

Reviews: