manualshive.com logo in svg

Gigabyte R282-G30, User Manual, Page: 105 / 109

Share
Download
Gigabyte R282-G30 User Manual Download Page 105

- 105 -

BIOS Setup

5-6  Boot Menu

The Boot menu allows you to set the drive priority during system boot-up. BIOS setup will display an error 

message if the legacy drive(s) specified is not bootable.  

Parameter

Description

Boot Configuration

Setup Prompt Timeout

Number of seconds to wait for setup activation key. 65535 (0xFFFF) 

means indefinite waiting.

Press the numeric keys to input the desired values.

Bootup NumLock State

Enable/Disable the Bootup NumLock function.
Options available: On, Off. Default setting is 

On

.

Quiet Boot

Enable/Disable showing the logo during POST.
Options available: Enabled, Disabled. Default setting is 

Enabled

.

Setup Flash

Press [Enter] to run setup flash.

Dump full Setup Data

Press [Enter] to dump full setup data to file.

Dump non-default Setup Data

Press [Enter] to dump non-default setup data to file.

Restore Setup Data

Press [Enter] to restore setup data from file.

Boot mode select

Selects the boot mode.
Options available: LEGACY, UEFI. Default setting is 

UEFI

.

Summary of Contents for R282-G30














































































































Reviews:

No comments