Gigabyte R182-M80 User Manual Download Page 99

Page: 99 / 109

- 99 -

BIOS Setup

5-4-4

BMC Network Configuration

Parameter

Description

BMC network configuration

Lan Channel 1

Configuration Address source

Selects to configure LAN channel parameters statically or dynamically

(DHCP). Do nothing option will not modify any BMC network parameters
during BIOS phase.

Options available: Unspecified, Static, DynamicBmcDhcp. Default setting

DynamicBmcDhcp

Station IP address

Displays IP Address information.

Subnet mask

Displays Subnet Mask information.
Please note that the IP address must be in three digitals, for example,
192.168.000.001.

Router IP address

Displays the Router IP Address information.

Station MAC address

Displays the MAC Address information.

Real-time get BMC network
address

Press [Enter] will set LAN mode and Address source and then get IP,
Subnet, Gateway and MAC address.

Summary of Contents for R182-M80














































































































Search results

Summary of Contents for R182-M80

Reviews:

Related manuals for R182-M80

Brands by name

Popular brands

Gigabyte R182-M80, User Manual

Search results

Summary of Contents for R182-M80

Reviews:

Related manuals for R182-M80

Brands by name

Popular brands