Gigabyte R161-R12 Service Manual Download Page 113

Page: 113 / 123

- 113 -

BIOS Setup

5-7 Boot Menu

The Boot menu allows you to set the drive priority during system boot-up. BIOS setup will display an error

message if the legacy drive(s) specified is not bootable.

Parameter

Description

Boot Configuration

Setup Prompt Timeout

Number of seconds to wait for setup activation key. 65535 (0xFFFF)

means indefinite waiting.

Press the numeric keys to input the desired values.

Bootup NumLock State

Enable/Disable the Bootup NumLock function.
Options available: On/Off. Default setting is

Quiet Boot

Enable/Disable showing the logo during POST.
Options available: Enabled/Disabled. Default setting is

Enabled

New Boot Option Policy

Controls the placement of newly detected UEFI boot options.
Options available: Default, Place First, Place Last. Default setting is

Default

Summary of Contents for R161-R12




























































































































Search results

Summary of Contents for R161-R12

Reviews:

Related manuals for R161-R12

Brands by name

Popular brands

Gigabyte R161-R12, Service Manual

Search results

Summary of Contents for R161-R12

Reviews:

Related manuals for R161-R12

Brands by name

Popular brands