Motherboard Components
1
2
3
4
5
6
7
9
8
10
11
12
13
14
15
17 16
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
38
37
No.
Code
Description
1
USB3_LAN1
LAN port #1 (top/server management LAN port)
/ USB 3.0 ports (bottom)
2
USB2_LAN2
LAN port #2 (top) / USB 2.0 ports (bottom)
3 VGA
VGA port
4
COM1
Serial port
5
BUZZER
Buzzer
6
PMBUS
PMBus connector
7
P2
8 pin power connector (for CPU)
8
DIMM_P0_B1
Channel 2 slot 1
9
DIMM_P0_B0
Channel 2 slot 0
10
DIMM_P0_A1
Channel 1 slot 1
11
DIMM_P0_A0
Channel 1 slot 0
12
BIOS_RCVR
BIOS recovery jumper
1-2 Close: Normal operation. (Default setting)
2-3 Close: BIOS recovery mode.
13
ME_RCVR
ME recovry jumper
1-2 Close: Normal operation. (Default setting)
2-3 Close: ME recovery mode.
14
CASE_OPEN
Case open intrusion alert header
15
P1
24 pin main power connector
16
CPU0_FAN
CPU fan connector
17
CPU0
Intel LGA1151 Socket H4
18
BAT
Battery socket
19
CLR_CMOS
Clear CMOS jumper
20
BIOS_PWD
Clearing Supervisor Password jumper
1-2 Close: Normal operation. (Default setting)
2-3 Close: Skip supervisor password.
21
SATA_0_1
SATA 3 6Gb/s connectors
22
SATA_2_3
SATA 3 6Gb/s connectors
23
SATA_DOM4
SATA port 4 DOM power connector
24
SATA4/SATA5
SATA 3 6Gb/s connectors (Supports SATA DOM) header
25
SATA_DOM5
SATA port 5 DOM power connector
26
USB_A1
Type A USB 2.0 connector
27
F_USB3
USB 3.0 header
28
F_USB2
USB 2.0 header
29
FP_1
Front panel header
30
IPMB
IPMB connector
No.
Code
Description
31
M2_MKEY
M.2 slot (Dimension: 2280)
32
TPM
TPM module connector
33
BP_1
HDD back plane board header
34
COM2
Serial port cable connector
35
PCIE_1
PCI Express x8 slot
36
PCIE_2
PCI Express x16 slot
37
ME_UPDATE
ME update jumper
38
S3_MASK
S3 Power On Select jumper
1-2 Close: Stop an initial power on when BMC is not ready.
2-3 Close: Keep initial power on. (Default setting)
System Components
No
Description
1
HDD bays
2
System fan #14 (FAN14)
3
System fan #12 (FAN12)
4
System fan #8 (FAN8)
5
System fan #6 (FAN6)
6
System fan #4 (FAN4)
7
CPU heat sink
8
Memory slots
9
PCIe riser bracket
10
Power supply cage
CAUTION!
To connect system fan connector, follow the instruction:
Blue/Red cable connect to odd numbered connector.
White/Amber cable connect to even numbered connector.
CAUTION!
Before you remove or install the system
cover:
Make sure the system is not turned on
or connected to AC power.
注意！
在卸下或安装系统机盖之前，请注意
下列事项：
确保系统未开启且未连接到交流电源。
注意！
蓝/红电缆连连接于单数风扇插座。
白/橘电缆连连接于双数风扇插座。
1
2
3 4
5
6
7
9
8
10
Front Panel Header
No.
Pin Define
1
Power LED+
3
No Pin
5
Power LED-
7
HDD LED+
9
HDD LED-
11
Power Button
13 GND
15
Reset
17 GND
19
ID
21
ID Switch-
23
NMI Switch-
No.
Pin Define
2
5V Standby
4
ID LED+
6
ID LED-
8
System Front Board LED+
10
System Status LED-
12
LAN1 Active LED+
14
LAN1 Link LED-
16
SMBus Data
18
SMBus Clock
20
Case Open
22
LAN2 Active LED
24
LAN2 Link LED-
1
24
23
2
HDD Back Plane Board Header
1 2
25 26
No.
Pin Define
1 BP_SGP_CLK
3 BP_SGP_GLD
5 BP_SGP_DOUT
7
Key Pin
9 GND
11 BP_LED_G_N
13 BP_SGP_DIN
15 GND
17 GND
19 P_3V3_AUX
21 P_3V3_AUX
23 GND
25 BP_PRESENSE
No.
Pin Define
2
No Connect
4 FAN_SGP_Gate
6 GND
8 Reset
10 BP_LED_A_N
12 GND
14
No Connect
16 SMB_BP_DATA
18 SMB_BP_CLK
20 BMC_ACK
22 BMC_REQ
24
Key Pin
26 GND
System Cover
1
1
2
1
1
Fan Duct
1
2
Heat Sink
1
2
3
Memory Population Configuration
Type
Ranks Per
DIMM and
Data Width
Speed (MT/s);
Slot Per Channel (SPC) and
DIMM Per Channel (DPC)
UDIMM
Unbuffered
DDR4 ECC
UDIMM
Unbuffered
DDR4 non-ECC
SR
1.2V
1.2V
2133
2133
Supported
Voltage
DR
2133
2133
2 Slot Per Channel
1DPC
2DPC
All channels in system run at the fastest common frequency.
Mixing ECC and non-ECC UDIMMs anywhere on the platform is not
supported.
1 and 2 DPC is supported at 2133MHz.
所有通道模式以最快的频率速度运行。
此主板不支持ECC与非ECC内存模组混合使用。
1
与
2 DPC
均支持
2133MHz
速度
。
System Fan
CAUTION!
Before you remove or install the system fan:
Make sure the system is not turned on or
connected to the AC power.
Disconnect all necessary cable connections.
Failure to observe these
warnings could result in personal injury or
damage to the equipment.
注意！
确保系统未开机且未连接到交流电源。
断开所有必要的线缆连接。若不遵循这些
警告，可能造成人员伤害或设备损坏。
2
1
No
Description
1
HDD#3
2
HDD#2
3
HDD#1
4
HDD#0
5
SGPIO header
6
Fan connector#13
7
Fan connector#14
8
Fan connector#11
9
Fan connector#12
10
ODD power connector
11
Fan connector#9
HDD Backplane Board Components
No
Description
12
Fan connector#10
13
Fan connector#7
14
Fan connector#8
15
Fan connector#5
16
Fan connector#6
17
Fan connector#3
18
Fan connector#4
19
Fan connector#1
20
Fan connector#2
21
Fan connector#15
22
Fan connector#16
Hard Disk Drive and Back Plane Board
3
4
4
1
2
5
1
2
3
4
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
System Front View
System Rear View
No
Description
1
USB 3.0 ports
2
ID button with LED
3
Power button with LED
4
HDD bays
No
Description
1
Power supply module cord socket
2
Power supply fan
3
Serial port
4
VGA port
5
USB 2.0 ports
6
GbE LAN port
7
10/100/1000 Server management LAN port
8
USB 3.0 ports
9
Low-profle riser card bay
Front & Rear
Power button/LED:
Green On
Off
Description
System is powered on
System is powered off
State
3 4 5 6 7 8
9
1
2
Speed LED
Link/Activity
LED
Off
State
Description
Yellow On
1Gbps data rate
Green On
100Mbps data rate
10Mbps data rate
10/100/1000 LAN LED:
4
2
3
1
PCI Express Card
3
4
5
注意！
在安装扩展卡前，请注意下列事项：
确保系统未开启且未连接到交流电源。
CAUTION!
Before you remove or install the PCI express card:
Make sure the system is not turned on or connected to AC power.
7
6
注意！
在替换或安装电源前，请注意下列事项：
确保系统未开启且未连接到交流电源。
CAUTION!
Before you remove or install the power supplies:
Make sure the system is not turned on or connected to AC power.
Power Supply
1
4
3
4
2
Rail Kit
Release
Lock out
⯮ⅎ庳⎽⇡
Release and detach the inner member from the slide
1
M4X6
Click
Aach the unit to the inner member
⯭Ⅼ彏擨ᷱ㜡⏗
2
Release
lock in
Insert the unit to complete the installaon
墬⅌㜡㞝
4
Bracket
M6X13
M6-NUT
Fix the outer member/bracket assembly to the frame
⯭⣽彏㈿㞝擨⅌㜡㞝
3
Front Panel LED and Buttons
3
4
2
3
4
7
5
6
1
7
复位按钮
按此按钮启动系统。
3
按下按钮启动系统识别功能。
ID按钮
3
系统处于开机状态。
系统处于ACPI S1状态（睡眠模式）。。
系统未开机或处于ACPIS5状态（关机状态）。
系统处于ACPI S4状态（休眠模式）。
电源按钮和LED
绿色
绿色
恒亮
不亮
闪烁
无亮灯
1/6
恒亮
不亮
闪烁
系统和网络之间的链接
网络访问
断开连接/待机
绿色
绿色
无亮灯
LAN3/LAN4活动LED
LAN1/LAN2活动LED
6
硬盘驱动器定位
硬盘驱动器访问
硬盘驱动器访问
硬盘故障
无硬盘驱动器访问
绿色
橙色
绿色/橙色
不亮
亮
亮
闪烁
无亮灯
硬盘驱动器LED
闪烁
编号
名称
颜色
状态
说明
4
系统正常运行
。
橙色
绿色
系统状态LED
恒亮
恒亮
不亮
不亮
闪烁
无亮灯
效能降低情形，可能为下列状况：
处理器问题
内存问题
严重情形，可能为下列状况：
电源模块故障
系统风扇故障
电源电压问题
系统温度/电压问题
非严重情形，可能为下列状况：
冗余电源模块故障
系统温度/电压问题
机箱侵入
系统未正常运行，可能为下列状况：
POST错误
NMI错误
处理器或终结器缺失
No.
Name
Color
Status
Description
7
Reset Button
Press the button to reset the system.
3
Press the button to activate system identifcation.
ID Button
2
System is powered on.
System is in ACPI S1 state (sleep mode).
System is not powered on or in ACPI S5 state (power off).
System is in ACPI S4 state (hibernate mode).
Power Button and LED
Green
Green
Solid On
Off
Blink
N/A
5
HDD locate
HDD access
HDD access
HDD fault
No HDD access or no HDD fault.
Green
Amber
Green/Amber
On
Off
Blink
On
Blink
N/A
HDD Status LED
1/6
Link between system and network or no access.
Data transmission or receiving is occurring.
No data transmission or receiving is occurring.
Solid On
Off
Blink
Green
Green
N/A
LAN3/4 Active/Link LEDs
LAN1/2 Active/Link LEDs
颜色
状态
4
System is operating normally.
Degrade condition, may indicates:
CPU failure
DIMM killed
System Status LED
Green
Amber
Solid On
Critical condition, may indicates:
Power module failure
System fan failure
Power supply voltage issue
System temperature
Solid On
Non-critical condition, may indicates:
Redundant power module failure
Temperature and voltage issue
Chassis intrusion
System is not ready, may indicates:
POST error
NMI error
Processor or terminator missing
Blink
N/A
N/A
Off
1
2
R121-X30 Quick Installation Guide/R121-X30
快速安装手册
