Gigabyte G492-Z51 User Manual Download Page 71

Page: 71 / 117

- 71 -

BIOS Setup

5-2-12

Network Stack Configuration

(Note) This item appears when

Network Stack

is set to

Enabled

Parameter

Description

Network Stack

Enable/Disable the UEFI network stack.
Options available: Enabled/Disabled. Default setting is

Enabled

Ipv4 PXE Support

(Note)

Enable/Disable the Ipv4 PXE feature.
Options available: Enabled/Disabled. Default setting is

Enabled

Ipv4 HTTP Support

(Note)

Enable/Disable the Ipv4 HTTP feature.
Options available: Enabled/Disabled. Default setting is

Disabled

Ipv6 PXE Support

(Note)

Enable/Disable the Ipv6 PXE feature.
Options available: Enabled/Disabled. Default setting is

Disabled

Ipv6 HTTP Support

(Note)

Enable/Disable the Ipv6 HTTP feature.
Options available: Enabled/Disabled. Default setting is

Disabled

IPSEC Certificate

(Note)

Enable/Disable the IPSEC Certificate feature.

PXE boot wait time

(Note)

Wait time in seconds to press ESC key to abort the PXE boot.
Press the <+> / <-> keys to increase or decrease the desired values.

Media detect count

(Note)

Number of times the presence of media will be checked.
Press the <+> / <-> keys to increase or decrease the desired values.

Summary of Contents for G492-Z51






















































































































Search results

Summary of Contents for G492-Z51

Reviews:

Related manuals for G492-Z51

Brands by name

Popular brands

Gigabyte G492-Z51, User Manual

Search results

Summary of Contents for G492-Z51

Reviews:

Related manuals for G492-Z51

Brands by name

Popular brands