Gigabyte G492-Z51 User Manual Download Page 105

Page: 105 / 117

- 105 -

BIOS Setup

5-6-1 System Event Log

Parameter

Description

Enabling / Disabling Options

SEL Components

Change this item to enable or disable all features of System Event
Logging during boot.
Options available: Enabled/Disabled. Default setting is

Enabled

Erasing Settings

Erasing SEL

Choose options for erasing SEL.
Options available: No/Yes, On next reset/Yes, On every reset. Default
setting is

When SEL is Full

Choose options for reactions to a full SEL.
Options available: Do Nothing/Erase Immediately. Default setting is

Nothing

Custom EFI Logging Options

Log EFI Status Codes

Enable/Disable the logging of EFI Status Codes (if not already converted
to legacy).
Options available: Disabled/Both/Error code/Progress code. Default
setting is

Error code

Summary of Contents for G492-Z51






















































































































Search results

Summary of Contents for G492-Z51

Reviews:

Related manuals for G492-Z51

Brands by name

Popular brands

Gigabyte G492-Z51, User Manual

Search results

Summary of Contents for G492-Z51

Reviews:

Related manuals for G492-Z51

Brands by name

Popular brands