Gigabyte G492-ID0 User Manual Download Page 77

Page: 77 / 108

- 77 -

BIOS Setup

5-3-3

UPI Configuration

Parameter

Description

UnCore General

Configuration

Press [Enter] to configure advanced items.

Uncore Status

– Press [Enter] to view the Uncore status.

Link Frequency Select

– Selects the UPI link frequency.

– Options available: 9.6GT/s, 10.4GT/s, 11.2GT/s, Auto. Default setting

Auto

SNC (Sub NUMA)

– Enable/Disable Sub NUMA Cluster function.

– Options available: Disable, Enable SNC2 (2-clusters). Default setting

Disable

Stale AtoS

– Enable/Disable Stale A to S directory optimization.

– Options available: Disable, Enable, Auto. Default setting is

Auto

LLC dead line alloc

–

Enable/Disable fill dead lines in LLC.

– Options available: Disable, Enable, Auto. Default setting is

Enable

Summary of Contents for G492-ID0













































































































Search results

Summary of Contents for G492-ID0

Reviews:

Related manuals for G492-ID0

Brands by name

Popular brands

Gigabyte G492-ID0, User Manual

Search results

Summary of Contents for G492-ID0

Reviews:

Related manuals for G492-ID0

Brands by name

Popular brands