manualshive.com logo in svg

Gigabyte E152-ZE0, User Manual

Share
Download
Gigabyte E152-ZE0 User Manual Download Page 123

- 45 -

BIOS Setup

5-6  Server Management Menu

Parameter

Description

FRB-2 Timer

Display the FRB-2 Timer staus. This item is not configurable. 

FRB-2 Timer 
timeout

Configures the FRB2 Timer timeout.

Options available: 3 minutes, 4 minutes, 5 minutes, 6 minutes. Default setting is 

6 

minutes

.

FRB-2 Timer Policy

Configures the FRB2 Timer policy.

Options available: Do Nothing, Reset, Power Down, Power Cycle. Default setting is 

Do Nothing

.

OS Watchdog 
Timer

Enable/Disable OS Watchdog Timer function.
Options available: Enabled/Disabled. Default setting is 

Disabled

.

OS Wtd Timer 
Timeout

Configures OS Watchdog Timer.

Options available: 5 minutes, 10 minutes, 15 minutes, 20 minutes. Default setting is 

10 minutes

.

Please note that this item is configurable when OS Watchdog Timer is set to 

Enabled.

OS Wtd Timer 
Policy

Configure OS Watchdog Timer Policy.

Options available: Reset, Do Nothing, Power Down. Default setting is 

Reset

.

Please note that this item is configurable when OS Watchdog Timer is set to 

Enabled.

Summary of Contents for E152-ZE0











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands