GIGA-BYTE TECHNOLOGY MZ72-HB2 User Manual Download | Manualshive

Page: 123 / 124

background image

- 123 -

BIOS Setup

2-10 BIOS Recovery

The system has an embedded recovery technique. In the event that the BIOS becomes corrupt the boot block
can be used to restore the BIOS to a working state. To restore your BIOS, please follow the instructions listed
below:

Recovery Instruction:

1. Copy the XXX.rom to USB diskette.

2. Setting BIOS Recovery jump to enabled status.

3. Boot into BIOS recovery.

4. Run Proceed with flash update.

5. BIOS updated.

«
...
121
122
123
124
»

Summary of Contents for MZ72-HB2





























































































































Reviews:

No comments

Related manuals for MZ72-HB2

Brand: ASROCK Pages: 80

Brand: MATSONIC Pages: 76

Brand: JETWAY Pages: 48

Z270 Gaming Pro Carbon Motherboard

Brand: MSI Pages: 92

IONITX-N series

Brand: Zotac Pages: 50

Brand: EVGA Pages: 2

Brand: MINATO Pages: 125

Brand: Maxim Pages: 7

SAM9N12/CN11-EK

Brand: Atmel Pages: 69

i.MX 8M Mini SODIMM SOM

Brand: iWave Pages: 16

THUNDER I7501 XTREME

Brand: TYAN Pages: 48

Brand: Analog Devices Pages: 16

Brand: DFI Pages: 138

Brand: DFI Pages: 134

Brand: DFI Pages: 183

Brand: A-Trend Pages: 49

Brand: ASROCK Pages: 5

Brand: ASROCK Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands