GIGA-BYTE TECHNOLOGY G481-HA1 Service Manual Download Page 79

Page: 79 / 124

- 79 -

BIOS Setup

5-2-15

USB Configuration

(Note) This item is present only if you attach USB devices.

Parameter

Description

USB Configuration

USB Devices:

Displays the USB devices connected to the system.

XHCI Hand-off

Enable/Disable the XHCI (USB 3.0) Hand-off support.
Options available: Enabled/Disabled. Default setting is

Enabled

USB Mass Storage Driver
Support

(Note)

Enable/Disable the USB Mass Storage Driver Support.
Options available: Enabled/Disabled. Default setting is

Enabled

Port 60/64 Emulation

Enables the I/O port 60h/64h emulation support. This should be enabled
for the complete USB Keyboard Legacy support for non-USB aware OS.
Options available: Enabled/Disabled. Default setting is

Enabled

Summary of Contents for G481-HA1





























































































































Search results

Summary of Contents for G481-HA1

Reviews:

Brands by name

Popular brands

GIGA-BYTE TECHNOLOGY G481-HA1, Service Manual

Search results

Summary of Contents for G481-HA1

Reviews:

Brands by name

Popular brands