manualshive.com logo in svg

GIGA-BYTE TECHNOLOGY G481-HA1, Service Manual

Share
Download
GIGA-BYTE TECHNOLOGY G481-HA1 Service Manual Download Page 39

- 39 -

System Hardware Installation

3-9  Installing the 3.5" Hard Disk Drive

Read the following guidelines before you begin to install the hard disk drive:

• 

Take note of the drive tray orientation before sliding it out.

•  The tray will not fit back into the bay if inserted incorrectly.
• 

Make sure that the HDD is connected to the HDD connector on the frontplane.

Follow these instructions to install a 3.5" hard disk drive: 

1.  Press the release button.

2.  Extend the locking lever.
3.  Pull the locking lever to remove the HDD tray. 

4.  Slide the hard disk drive into the blank HDD tray.

5.  Slide the hard drive tray into the bay until it locks in place.

CAUTION!

We strongly recommend using enterprise level hard disk drives in the Gigabyte server system. For 
more information of recommended HDDs, please visit the Gigabyte website: 

https://www.gigabyte.com

 and search for the specific product QVL from 

Support & Downloads.

1

2

3

4

Summary of Contents for G481-HA1





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands