manualshive.com logo in svg

GIGA-BYTE TECHNOLOGY G481-HA1, Service Manual

Share
Download
GIGA-BYTE TECHNOLOGY G481-HA1 Service Manual Download Page 30

System Hardware Installation

- 30 -

3-5  Installing the PCIe Card

Read the following guidelines before you begin to install the PCIe Card:  

• 

Voltages can be present within the server whenever an AC power source is connected. This 
voltage is present even when the main power switch is in the off position. Ensure that the system 
is powered down and all power sources have been disconnected from the server prior to installing 
a PCIe card. Make sure the system is not turned on or connected to AC power.

• 

Failure to observe these warnings could result in personal injury or damage to the equipment.

Follow these instructions to install the PCIe card:

1.  Pull out the thumbnail screw securing the GPU card cage in place.
2.  Flip over the GPU card cage in the direction indicated.

3.  Remove the two screws securing the PCIe card slot covers in place and remove the PCIe card slot 

covers.

4.  Insert the PCIe card into the selected slot. Make sure the PCIe card is properly seated.

5.  Install the two screws to secure the PCIe card in place.

1

2

Summary of Contents for G481-HA1





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands