MAIN UNIT SETUP (Fig. 1)
PROGRAM THE COMPUTER (ALL CLEAR)
1. A battery is already loaded in the main unit when purchased.
2. Hold down the SET button
and RESET button
simultaneously for more than 3
seconds to program the computer and clear all data.
IMPORTANT: Be sure to program
the computer before it is be used, otherwise the computer may run errors.
3. The LCD segments will be tested automatically after the unit is programmed.
4. Press MODE button
to stop LCD test, then the flickering "KM/H".
UNIT SELECTION
Press MODE button
to choose KM/H or M/H. Then press the SET button
to store selection.
WHEEL CIRCUMFERENCE
1. Roll the wheel until the valve stem at its lowest point close to the ground, then mark this
first point on the ground.
(Fig. a)
2. Get on the bike and have a helper push you until the valve stem returns to its
lowest point. Mark the second point on the ground. (Sitting on the bike achieves a more
accurate reading since the weight of the rider slightly changes the wheel circumference).
3. Measure the distance between the marks in millimeters. Enter this value to set the wheel
circumference.
Option: Get a suitable circumference value from the table.
(Fig. b)
4. Adjust the wheel circumference as the data setting process.
5. Unit will change to the normal operation after this circumference setting.
FUNCTIONS (Fig. 3)
:
Current Speed
0.0–199.9Km/h (120.0 Mile/h), 0.1Km/h (Mile/h), +/- 1%
The current speed is always displayed on the upper set when riding. It displays current
speed up to 199.9 Km/h or 120.0 Mile/h (for wheel diameters over 24 inches).
CLK:
12HR or 24HR Clock
1H00M–12H59M or 0H00M–23H59M, 1 Minute, +/- 0.3%
It can display the current time either in 12HR or 24HR clock.
DST:
Trip Distance
0.00–999.99Km (Miles), 0.01Km (Mile), +/- 0.01%
The DST function accumulates the distance data from the last RESET operation as long as
the bike is being ridden.
RTM:
Riding Time
0M00S-59M59S, 1 Second, 0H00M-99H59M, 1 Minute, +/- 0.03%
1. The RTM totals the riding time from the last RESET operation.
2. It displays in 1 second increments when RTM is less than 1 hour and changes to 1 Minute
increments after 1 hour. It will restart from zero after 100 hours.
AVG:
Average Speed 0.0–199.9Km/h (120.0Mile/h), 0.1Km/h (Mile/h), +/- 0.1%
1. It is calculated from the DST divided by the RTM. The average data counted is from the
last RESET to current point.
2. It will display "0.0" when RTM is less than 4 seconds.
3. It is updated about one second when RTM is over 4 seconds.
TROUBLE SHOOTING
Check the following before taking unit in for repairs.
MAX:
Maximum Speed
0.0–199.9Km/h (120.0Mile/h), 0.1Km/h (Mile/h), +/- 1%
It shows the highest speed from the last RESET operation.
TMP:
Current Temperature °C / °F -10°C ~ 60°C (14°F ~ 140°F)
ODO:
Odometer 0-99999Km (Miles), 1Km (Miles), ± 0.1%
The ODO accumulates total distance as long as the bicycle is running, the ODO data can be
cleared by the All Clear operation only.
ODO1, ODO2:
Bike1 odometer, Bike2 odometer
0.0–99999.9 Km (Miles), 0.1Km (Mile), +/- 0.1%
1. The odometer cumulates the total distance as long as the bike is running.
2. This computer design has 2 wheel circumference memories to calculate data for 2 bikes.
The odometer is separated for each bike.
3. It displays one ODO data only when the bike is selected in the current status.
T.RT:
Total Riding Time
0H00M-999H59M, 1 Minute, +/- 0.003%
The T.RT totals the riding time from the last ALL CLEAR operation.
: SCAN
1. Auto-Scanning Display Mode.
Press the MODE button
till the symbol is displayed. The computer will change the
display modes in a loop sequence automatically every 5 seconds.
2. Fixed Display Mode.
Press the MODE button
to turn off the symbol and select a desired display mode; the
computer will stop the auto-scanning display operation.
/ : Speed Pacer
It flashes the speed pacer arrow while the current speed is higher than the average speed
and the down arrow flickers conversely.
BUTTON AND OPERATIONS
MODE BUTTON
Quickly press this button to move in a loop sequence from one function screen to another.
LOCK/SET BUTTON
Hold down this button 2 seconds to get in or out the setting screens when you want to reset
to bike, or the current time of the CLK.
LIGHT/RESET BUTTON
1. Light for 4 seconds after each press.
(Fig. 5)
2. The symbol " " will apper to indicate the EL back-light functuon is at working status.
3. Hold down the “RESET” button
till the LCD digit is blank, then release it.
The computer will RESET the DST, RTM, AVG, MAX.
CLOCK SETTING
1. Change the LCD display to CLK screen.
2. Press the SET button
to enter the clock adjusting screen to setting the clock.
3. A quick press of the MODE button
to select 12HR or 24HR.
4. Adjust the clock data as the data setting procedures.
RESET OPERATION (Fig. 4)
1. Hold down the RESET button
till the LCD screen is blank, then release it. The
computer will reset AVG, DST, RTM and MAX data from stored values to zero.
2. It cannot reset ODO, T.RT, CLK.
AUTOMATIC START/STOP
1. The computer will automatically begin counting data upon riding and stop counting data
when riding is stopped.
2. The flickering symbol " " indicates that the computer is at start status.
KEY-LOCK (Fig. 2)
To protect you computer, you may can press the lock button to lock the MODE button
Whenever you press the lock button, the functions of the MODE button
will be disabled.
You may can unlock the MODE button
by pressing the lock button
again.
AUTO SLEEP MODE
To preserve battery, this computer will automatically switch
to sleep mode and just displays
the CLK data when it has not been used for about 15 minutes. The power will be turned on
by pressing the SET
button
.
LOW BATTERY INDICATOR
1. The symbol " " will appear to indicate the battery is nearly exhausted.
2. Replace battery with a new one within a few days after the symbol was appeared,
otherwise the stored data may be lost when the battery voltage is too low.
BATTERY CHANGE (Fig. c)
1. All data will be cleared when battery is replaced.
2. This computer allows you to re-key in data of ODO which you have had rode after
replacing battery.
3. Keep record the ODO and T.RT data before you remove the old battery.
4. Replace with a new CR2032 battery in the compartment on the back of the computer
with the positive (+) pole toward the battery cap.
5. Program the main unit again.
PRECAUTIONS
1. Do not leave the main unit exposed to direct sunlight when you don't ride the bike.
2. Do not try to disassemble the main unit or its accessories.
English
Sensor:
No Contact Magnetic Sensor.
Battery Type:
3.0V Battery X 1 (Typical No. CR2032)
Battery Operating Life:
CR2032 in Main Unit About one year
(based on the average riding time of 1.5 hours per day)
CR2032 in Speed Transmitter Around 24000km
Dimensions/Weight:
34 x 52 x 15 mm / 21g
Wheel Circumference Setting:
1mm - 3999mm (1mm increment)
Operation Temperature:
0°C ~ 50°C (32°F ~ 122°F)
Storage Temperature:
-10°C ~ 60°C (14°F ~ 140°F)
3
4
RESET OPERATION (DST=0, RTM=0, AVG=0, MAX=0)
Bike 1 or Bike 2
1
+1
CYCLE COMPUTER
MODE
LOCK/
SET
LIGHT/
RESET
BATTERY CHANGE
Tire Size
Circumference
Nunber
18 Inch
1436 mm
20 Inch
1596
22 Inch
1759
24x1.75
1888
24 Inch
1916
24x 1 3/8
1942
26x1.40
1995
26x1.50
2030
26x1.75
2045
26x1.95
2099
26x2.1
2133
700C TUBULAR
2117
700x20C
2092
700x23C
2112
700x25C
2124
700x28C
2136
700x32C
2155
700x35C
2164
700x38C
2174
27.5 Inch
2193
28 Inch (700B)
2234
28.6 Inch
2281
b.
POPULAR TIRES
CIRCUMFERENCE
REFERENCE TABLE
15m
WHEEL CIRCUMFERENCE
a.
2nd 1st
EL Back-light
Data Setting Mode
c.
0~3
2s
OK!
2s
MODE
Low battery indicator
ON
OFF
Key-lock off
+1
0~3
0~9
0~9
+1
0
~
23
0
~
5
3s
+
CLOCK
DST
RTM
AVG
MAX
TMP
ODO
TRT
SCAN
SEGMENTS
LCD
AUTO TEST
ALL CLEAR UNIT SELECTION BIKE 1, BIKE 2 SETTING
CIRCUMFERENCE SETTING
CLOCK SETTING
2s
OK!
END SETTING
+1
0~9
0~9
+1
0~9
0~9
ODO SETTING
TRT SETTING
2
Key-lock
2s
DST
RTM
AVG
MAX
2s
OK!
DST
5
6
2s
3. Check relative position between sensor, magnet and main unit periodically.
4. Don’t use thinner, alcohol or benzine to clean the main unit or its accessories when
they become dirty.
5. Remember to pay attention to the road while riding.
WIRELESS
RESET
LIGHT
LOCK
SET
1. Is the battery dead?
2. Is there incorrect battery
installation?
1. Is it at the MAIN UNIT SETUP or
another setting screen?
2. Are the relative positions and gap
between sensor and magnet correct?
3. Is the circumference correct?
4. Is the sensing distance too long or
the installation angle of the sensor
incorrect?
5. Is the sensor battery nearly
exhausted?
6. Is any strong interference source
nearby?
Did you leave main unit under direct
sunlight when not riding the bike for a
long period of time?
Is the temperature below 0
°
C (32
°
F)?
1. Replace the battery.
2. Be sure that the positive pole of the
battery is facing the battery cap.
1. Refer to the setting procedure and
complete the adjustment.
2. Refer to
Installation
(
Fig
.
C-a.
)and
re-adjust position and gap correctly.
3. Refer to "Circumference Setting"
and enter correct value.
4. Refer to
Installation
(
Fig.C-b
.)adjust
distance or angle between the main
unit and the sensor.
5. Replace with a new battery.
6. Move away from the source of
interference.
Refer to the "Main Unit Setup" and
initiate the computer again.
Place main unit in the shade to return
to normal state.
No adverse effect on data.
Unit will return to normal state when
the temperature rises.
Main unit No
display
No current speed
or
Incorrect data
Irregular display
LCD is black
Display is slow
PROBLEM
CHECK ITEMS
REMEDY
Auto Sleep and
Key-lock on
4403006671
Gasket
Battery
CR2032
Battery
cap
3V
CR2032
+
3V
CR2032
+
Screwdriver
Screw
