background image

SC24

3  - INSTALLATION WARNINGS

4 - WARNINGS FOR THE USER

In  the  event  of  an  operating  fault  or  failure,  cut  the  power  upstream  of  the  control  unit  and  call  the  technical 
service. Periodically check the functioning of the safety devices. Any repairs must be carried out by specialised 
personnel using original and certified materials.
The  product  is  not  to  be  used  by  children  or  people  with  physical,  sensory  or  mental  capabilities,  or  lack  of 
experience  and  knowledge,  unless  they  have  been  given  instruction.  Do  not  touch  the  card  for  adjustments 
and/or maintenance.

Ÿ

Before proceeding with the installation, it is necessary to fit a magnetothermal  and  differential  switch  of  10A 
max.  upstream  of  the  system.  The  switch  must  guarantee  an  omnipolar  separation  of  the  contacts,  with  an 
opening distance of at least 3 mm.

Ÿ

To prevent possibile interferences, differentiate and always keep the power cables (min. cross-section 1,5mm²) 
separate from the signal cables (min. cross-section 0,5mm²).

Ÿ

Make the connections referring to the following tables and to the attached screen-print. Be extremely careful to 
connect in series all the devices that are connected to the same N.C. (normally  closed) input and in  parallel  all 
the devices that share the same N.O. (normally open) input. An incorrect installation  or  an  improper  use  of  the 
product may compromise the safety of the system.

Ÿ

Keep all the materials contained in the packaging away from children, since they pose a potential  risk.

Ÿ

The  manufacturer  declines  all  responsibility  for  improper  functioning  of  the  automated  device  if  the  original 
components and accessories suitable for the specific application are not used.

Ÿ

After the installation, always carefully check the proper functioning of the system and the devices used.

Ÿ

This instruction manual addresses persons qualified for installation of “live equipment”. Therefore good technical 
knowledge and professional practice in compliance with the regulations in force are required.

Ÿ

Maintenance must be carried out by qualified personnel.

Ÿ

Before carrying out any cleaning or maintenance operation, disconnect the control unit from the mains.

Ÿ

This control unit may only be used for the purpose for which it was designed.

Ÿ

Check the aim of the final use and make sure that all safety measures are taken.

Ÿ

The use of the products for purposes different from the intended use has not been tested by the manufacturer, 
therefore any work is carried out on full responsibility of the installer. 

Ÿ

Mark the automated device with visible warning plates.

Ÿ

Warn the user that children or animals must not play or stand around near the gate.

Ÿ

Appropriately protect the danger points (for example using a sensitive frame).

WARNING: IMPORTANT SAFETY INSTRUCTIONS.

It is important to follow the present instructions for your own safety.
Please keep this instruction manual.

UK

11

Summary of Contents for GI.BI.DI SC24





















Reviews: