manualshive.com logo in svg

GHM HONSBERG OMNIPLUS-F Series, Operating Manual

Share
Download
GHM HONSBERG OMNIPLUS-F Series Operating Manual Download Page 13

 

 

OMNIPLUS-F 

Mounting | 5 

C-E01_X__OMNIPLUS-F__DB2-1.0 

13/ 45 

5.3  Push-in probe with system mounting  

 

- 

OMNIPLUS-F-013TK031

 

- 

OMNIPLUS-F-013TK037

 

 

Push-in sensors with system mounting are mounted in the pipeline using a system  
T-piece (accessory) or a system welding or soldering socket provided for this purpose. 

They have a double O-ring seal and are fixed in the system piece with a union nut. 
The alignment of the X-marking is done without changing the immersion depth.  
Removal and reassembly in the application is easy, which facilitates inspection and 
cleaning of the sensors. An auxiliary tool is available as an accessory for correct  
alignment of the X mark even under difficult installation conditions. 

5.4  Push-in probe with 12 mm outer diameter and 

variable immersion depth  

 
-  OMNIPLUS-F-012VK100  
-  OMNIPLUS-F-012VK150 
-  OMNIPLUS-F-012VKxxx 

 

 

Push-in sensors with variable immersion depth are mounted in the pipeline using 
mounting fittings provided for this purpose.  

The following mounting fittings are available for this purpose: 

 
Weld-in adapter ADG-015GS026K, PN 40 

 

Pinch fitting with weld-in spigot 
ADQ-012S021K, PN 40 

 

 

 

Summary of Contents for HONSBERG OMNIPLUS-F Series














































Reviews:

No comments

Brands by name

Popular brands

Load more brands