gfm Peakanalyzer Installation Manual Download Page 33 | Manualshive

Page: 33 / 40

gfm Peakanalyzer Installation Manual Download Page 33

Peakanalyzer Installation Manual Version 2.6

33

Picture 24: Installation of displacement sensors at a wheel swing arm

2.6

Installation of speed sensors

Normally  the  speed  is  measurement  by  an  inductive  speed  sensor.  For  an  accurate
measurement  of  the  speed  it  is  recommended  to  measure  the  speed  at  the  shaft  with  the
highest speed.

Picture 25: Radial installation of a speed sensor

If the installation on the shaft with the highest speed is not possible, the installation can also
take place on a shaft with lower speed. In this case it is recommended to use multiple impulses
per rotation. One possibility to measure multiple impulses per rotation is shown in Picture 25.
If the output signal of the speed sensor is connected to input C of the speed terminal, the
impulses must not be equidistant distributed (see chapter 2.3.5).

During the adjustment of the speed sensor it has to be taken into consideration to not exceed
the required switching distance. The supplied speed sensor as shown in Picture 25 has a
switching distance of 9.5 mm.

«
...
31
32
33
34
35
...
»

Summary of Contents for Peakanalyzer









































Reviews:

No comments