background image

SIDE VIEW

Field Mount w/
8052 Integral kit

92 mm
(3.6 in.)

97 mm

(3.8 in.)

56 mm 
(2.2 in.)

41 mm 
(1.6 in.

)

Optional
Rear
Cover

Panel Mount

SIDE VIEW

FRONT VIEW

96 mm

(3.8 in.)

96 mm
(3.8 in.)

Field Mount &

Panel Mount

SIDE VIEW

Field Mount w/
8050 Universal base

106 mm (4.2 in.)

42 mm 

(1.7 in.)

64 mm 

(2.5 in.)

82 mm
(3.23 in.)

   8050

96 mm

(3.8 in.)

107 mm (4.2 in.)

42 mm 

(1.7 in.)

65 mm 

(2.5 in.)

   8052

Signet 8850-3 Conductivity/Resistivity Transmitter

2.  Specifi cations

General

Compatible electrodes:  Signet 3-28XX-1 Standard and Certi

fi

 ed 

Series Conductivity/Resistivity Electrodes

Accuracy:  ±2% of reading
Enclosure:
•  Rating: 

NEMA 4X/IP65 front

• Case: 

PBT

•  Panel Case Gasket:  Neoprene
•  Window: 

Polyurethane coated polycarbonate

•  Keypad: 

Sealed 4-key silicone rubber

•  Weight: 

Approx. 325g (12 oz.)

Display:
•  Alphanumeric 2 x 16 LCD
•  Contrast:  User selected, 5 levels
•  Update rate: 1.8 seconds

Electrical

•  Power:  12 to 24 VDC ±10%, regulated, 100 mA max.
Sensor input range:  
•  Conductivity:  0.01 

μ

S/cm to 400 000 

μ

S/cm

•  Resistivity:   

10 K

•cm to 100 M

•cm

•  TDS: 0.023 to 200 000 PPM nominal (adjustable 

μ

S/PPM)

•  Temperature: 

PT 1000, -25 °C to 120 °C (-13 °F to 248 °F)

 

Measurements above 10 M

 (below  0.1 

μ

S) must be performed 

in solution temperatures from 20 °C  to 100 °C.

Two 4 to 20 mA Outputs:
•  Passive, isolated, fully adjustable and reversible 4 to 20 mA 

outputs are independently source selectable for conductivity or  
temperature.

•  Max Loop Impedance:   

  50 

 max. @ 12 V

 

   

325 

 max. @ 18 V

 

   

600 

 max. @ 24 V

•  Update Rate:  200 ms
•  Accuracy:  ±0.03 mA @ 25°C, 24 V
Open-collector output, optically isolated:
•  50 mA max. sink, 30 VDC maximum pull-up voltage.
• Programmable 

for:

 

•  High or Low with adjustable hysteresis

 

•  Pulse operation (max rate: 400 pulses/min).

Environmental

Operating Temperature: 

-10 °C to 70 °C (14 °F to 158 °F)

Storage Tmperature: 

-15 °C to 80 °C (5 °F to 176 °F)

Relative Humidity:   

0 to 95%, non-condensing

•  Maximum Altitude: 

2000 m (6562 ft)

• Insulation 

Category:  II

• Pollution 

Degree: 

2

Standards and Approvals

•  CE, UL listed
•  Manufactured under ISO 9001 for Quality, ISO 14001 for 

Environmental Management and OHSAS 18001 for Occupational 
Health and Safety.

 

China RoHS (Go to www.gfsignet.com for details)

 

Declaration of Conformity according to FCC Part 15

 

This device complies with Part 15 of the FCC rules. Operation is 
subject to the following two conditions:

 

(1) This device may not cause harmful interference, and, 

 

(2) This device must accept any interference received, including 
interference that may cause undesired operation.

Signet 

Conductivity/Resistivity

Transmitter

ENTER

62.50 uS/cm

25.0 C

CAUTION!

•    Remove power to unit before wiring 

input and output connections.

•    Follow instructions carefully to avoid 

personal injury.

Contents

1. Installation
2. Speci

fi

 cations

3. Electrical Connections
4. Menu Functions

1. Installation 

ProcessPro transmitters are available in two styles: panel mount and 

fi

 eld mount. The panel mount is supplied with the necessary 

hardware to install the transmitter. This manual includes complete panel mounting instructions.
Field mounting requires a separate mounting kit. The 3-8050 Universal kit enables the transmitter to be installed virtually 
anywhere. Detailed instructions for 

fi

 eld installation options are included with the 3-8050 Universal kit.

1.1 Panel 

Installation 

  1.  The panel mount transmitter is designed for installation using a 1/4 DIN Punch. For manual panel cutout, an adhesive 

template is provided as an installation guide.  Recommended clearance on all sides between instruments is 1 inch.

  2.  Place gasket on instrument, and install in panel.
  3.  Slide mounting bracket over back of instrument until quick-clips snap into latches on side of instrument.
  4.  To remove, secure instrument temporarily with tape from front or grip from rear of instrument.  DO NOT RELEASE.
 

  Press quick-clips outward and remove.

3-8850.090-3   

Rev. K 11/12 

 

English

*3-8850.090-3*

English

Summary of Contents for Signet 8850-3













Reviews: