GEZE TSA 325 NT Installation Instructions Manual Download Page 8

Page: 8 / 112

Revolving door TSA 325 NT

Installation

4.1 Preparations to be made on site

Check the preparations made on site by the customer to ensure proper installation:

Type and load capacity of the façade construction or suspending frame.

Evenness of the installation surface.

Cable plan requirements.

Observe installation height/metre level mark at the construction site.

4.2 Mounting the revolving door TSA 325 NT

Secure workplace against unauthorised entry.

Always work with a second person.

Use a stepladder or step stool.

Keep inside area of track clean.

4.2.1 Mounting the floor ring

Lay 2 floor ring halves (1) and (2) together.

Determine the position of the floor ring.

Screw the 2 floor ring halves together using

screws, nuts and washers.

Summary of Contents for TSA 325 NT

















































































































Search results

Summary of Contents for TSA 325 NT

Reviews:

Brands by name

Popular brands

GEZE TSA 325 NT, Installation Instructions Manual

Search results

Summary of Contents for TSA 325 NT

Reviews:

Brands by name

Popular brands