GEZE TSA 325 NT Installation Instructions Manual Download

Page: 43 / 112

Revolving door TSA 325 NT

Options

5.4 Open position monitoring

The leaf part of the tappet contact must be mounted on the roller carriage before installing the leaf. Subse-

quent installation on the roller carriage is not possible.

The leaf part tappet contacts can only be mounted on an RC 2 roller carriage.

Mounting the tappet contact on a track

The tappet contact consists of a leaf part and a frame part installed in the track.

Before installing the night-time closer, mount

the leaf part (1) on the associated RC 2 roller

carriage.

After installing the leaf in the track, align

the door leaf and check for proper running

behaviour, including in conjunction with the

tooth belt (optional: automatic night-time

closer).

After aligning the leaf, push the frame

element tappet contact (2) into the track from

below and position in the end position with

the door leaf. Then attach from below using

a fixing screw (3)

Summary of Contents for TSA 325 NT

















































































































Search results

Summary of Contents for TSA 325 NT

Reviews:

Related manuals for TSA 325 NT

Brands by name

Popular brands

GEZE TSA 325 NT, Installation Instructions Manual

Search results

Summary of Contents for TSA 325 NT

Reviews:

Related manuals for TSA 325 NT

Brands by name

Popular brands