IMPORTANT:
Read these instructions fully before using the heater.
Retain these instructions for future reference.
NOTE:
THESE HEATERS ARE INTENDED FOR DOMESTIC
USE ONLY.
SAFETY INSTRUCTIONS
(to be read before operating the heater)
1) Do not use the heater unless it is correctly mounted
to a wall, or the feet are correctly attached.
2) Ensure the power supply to the socket into which
the heater is plugged is in accordance with the rating
label on the heater and that the socket is earthed.
3) Keep the mains lead away from the hot body of
the heater.
4) The heater is not intended for use in bathrooms,
laundry areas or similar indoor locations. Never place
the heater where it may fall into a bathtub or other
water container.
5) Do not use outdoors.
6) Do not cover or obstruct any of the heat outlet grilles
or the air intake openings of the heater.
7) Do not place the heater on carpets having a very
deep pile.
8) Always ensure that the heater is placed on a firm
level surface. Ensure that the heater is not
positioned close to curtains or furniture as this
could create a fire hazard.
9) Do not position the heater in front of, or immediately
below, a wall socket.
10) Do not position the heater under a shelf unless a
minimum gap of 250mm exists between the top
edge of the heater and the underside of the shelf
11) Do not insert any object through the heat outlet or
air intake grilles of the heater.
12) Do not use the heater in areas where flammable
liquids are stored or where flammable fumes may
be present.
13) Particular care should be taken when the heater is
situated in areas occupied by children or invalids.
14) Always unplug the heater when moving it from one
location to another.
15) Do not use the heater if the power cord is damaged.
If the power cord is damaged it must be replaced
by a recognised service agent or other qualified
person. If the plug is damaged, see ‘Plug
Replacement’ details (back page).
Turbo Fan Operation - Models G2TCH and G2TCHT
1) These heaters incorporate an internal fan, which can be switched on independently of the
heating elements.
2)
Fan Operation:
This is operated by means of the switch with the fan symbol along side it.
The fan will only operate with the thermostat in the ‘on’ position and can be used when the
heating elements are ‘on’ to blow warm air around the room. In warm conditions the fan
can be used with the heating elements ‘off’ to blow cool air around the room.
Plug Replacement
If the plug is damaged and requires replacement, follow the wiring instructions supplied with
the new plug.
+
The green and yellow wire must be connected
to the terminal marked with the earth symbol
or coloured green or green and yellow.
+
The blue wire must be connected to the
terminal marked with the letter N or
coloured black/blue.
+
The brown wire must be connected to
the terminal marked with the letter L or
coloured red/brown.
+
A 13 amp plug to BS 1363 must be fitted with 13 amp fuse to BS 1362.
CLEANING THE HEATER
1) Always un-plug the heater from the wall socket and allow it to cool down before cleaning.
2) Clean the outside of the heater by wiping with a damp cloth and buff with a dry cloth.
Do not use any detergents or abrasives and do not allow any water to enter the heater.
STORING THE HEATER
When the heater is not used for long periods of time it should be protected from dust and
stored in a clean dry place.
Instructions for:
Convector heaters:
Models:
G2CH
2.0kW convector heater with
thermostat
G2CHT
2.0kW convector heater with
thermostat and timer
G2TCH
2.0kW convector heater with
thermostat and fan
G2TCHT
2.0kW convector heater with
thermostat, timer and fan
AR0937 Ed. A
RECYCLABLE
PACKAGING
NOTE:
This product should not be disposed of with household waste.
Please recycle where facilities exist.
Check with your local authority for recycling advice.
GET PLC,
Key Point, 3-17 High Street, Potters Bar,
Hertfordshire, EN6 5AJ, England
Helpline Telephone 0121 565 7770
www.getplc.com
AR0937 - VectorHeaters.qxd 15/7/05 15:29 Page 1
