background image

P.11

II. Special Functions

Timer

 

‧ 

Under standby mode, press “TIMER” to set  

  the power-on time. Continue pressing to  

  adjust the timer (from 1 to 24 hours). Timer  

  indicator turns on.

‧ 

Under power-on mode, press “TIMER” to set power- 

  off time. Continue pressing to adjust the timer (from  

  1 to 24 hours). Timer indicator turns on.

Sleep Function

 Press “SLEEP” to select sleep function. 

  Default fan speed is low.

‧ 

Under sleeping mode and when cooling  

  mode is selected, the temperature will raise  

  1

 from the set temperature after one hour,  

  and further raise 1

 after another hour, and  

  then remain the same. 

 Under sleep function and when heating  

  mode is selected, the temperature will drop  

  1

 from the set temperature after one hour 

  and further drop 1

 after another hour, and  

  then remain the same.  

 Sleep function cannot be selected under  

  dehumidifying and fan modes. 

 When “Water Full” indicator is on, machine  

  is in standby or operating mode is changed,  

  sleep function will be cancelled. 

  Note

  ‧

 Compressor will start to run for 3 min 

    after restart.

  ‧

 Restart the machine at least 3 min   

    after shutting down, in order to protect the  

    compressor.

II.特別功能

定時功能

‧ 於待機狀態,按「定時」鍵設定開機時間, 
    續按「定時」鍵調校定時時間 (1至24小 
    時),定時模式顯示燈會亮起。

‧ 於開機狀態,按「定時」鍵設定關機時間, 
    續按「定時」鍵調校定時時間 (1至24小 
    時),定時模式顯示燈會亮起。

睡眠功能

‧ 按「睡眠」鍵進入睡眠狀態,預設值是低 
    風速。
‧ 在「冷凍」模式下設定「睡眠」狀態,溫 
    度會於1小時後上升1℃,再於第2個小時上 
    升1℃,然後溫度保持不變。
‧ 在「暖風」模式下設定「睡眠」狀態,溫 
    度會於1小時後下降1℃,再於第2個小時下 
    降1℃,隨後溫度保持不變。
‧ 抽濕及風扇模式運作期間,不能啟動睡眠 
    模式。
‧ 於水滿、待機及轉換模式時,睡眠模式 
    會被取消。

注意

  ‧  重開本機約3分鐘後,壓縮機才會開始運作。

  ‧  關機後,請待最少3分鐘後才再次啟動,以確 
    保壓縮機壽命。

 

操作說明 

OPERATION INSTRUCTIONS

Summary of Contents for MAC-10

















Reviews: