Geolux RSS-2-300W User Manual Download Page 6

Page: 6 / 41

RSS-2-300W User Manual

RSS-2-300W Non-Contact Surface Velocity Radar

Connector Pin-Out

The surface velocity radar uses robust IP68 circular M12 connector with 12 positions and the

mating cable is also delivered with the surface velocity radar. The connector and cable details

are shown in Picture 1 while Table 2 gives a detailed description of each pin.

Picture 1. Surface Velocity Radar Connectors

Table 2. Connector and Cable Pin-out

Pin No.

Wire Color

Pin Name

Pin Description

White

GND

This pin should be connected to the ground

(negative) pole of the power supply

Brown

+Vin

The power supply for the Radar Speed Sensor

is provided on this pin. The Radar Speed Sensor

power supply voltage must be in the range 9

VDC to 27 VDC, and the power supply must be

able to provide at last 0.65W

Green

RS232 – TxD

RS-232 data transmit signal

Yellow

RS232 – RxD

RS-232 data receive signal

Grey

GND

Signal ground

Pink

CAN – H

CAN2.0B high signal

(optional)

Blue

CAN – L

CAN2.0B low signal

(optional)

Red

Reserved

Orange

RS485 – D-

RS-485 data transmitter/receiver low signal

Dark Red

RS485 – D+

RS-485 data transmitter/receiver high signal

Black

Alarm SW

Alarm - open collector switch signal max.

60mA (optional)

Purple

4 – 20 mA

Sink for 4 – 20 mA analog interface. Connect

sensing device as pull-up to sink the current

Summary of Contents for RSS-2-300W









































Search results

Summary of Contents for RSS-2-300W

Reviews:

Geolux RSS-2-300W, User Manual, Page: 6 / 41

Search results

Summary of Contents for RSS-2-300W

Reviews: