
Generation tariff
Your
Solo II PV
will start to show your energy generation as
soon as it’s installed. To get the most out of your display you’ll
need to enter your tariff.
About your generation tariff
Your utility will provide you with a generation tariff (also known
as ‘feed-in-tariff’ or ‘FIT’) and also tell you whether you have any
other payments as part of this tariff.
The
Solo II PV
shows a calculated approximation of earnings
from your PV array based on the configured generation tariff.
Calculated earnings do not include any other payments made
as part of your generation tariff.
k
Do not use figures from your
Solo II PV
to submit readings
to your utility - always take readings directly from the
generation meter.
Enter your generation tariff
Your generation tariff which will usually be shown as ‘per kWh’
and you don’t need to enter any other payment details.
To configure your generation tariff:
•
Press and hold
b
until
[BASIC]
shows;
•
Repeatedly press
b
until you see
FIT
and a number
flashing;
•
Use
a
and
c
to change the tariff and press
b
to set;
•
Repeatedly press
b
until you exit the settings screens.
Once your generation tariff has been entered, your
Solo II PV
will start to show you how much your PV array is earning.
Settings
For information on other settings for your
Solo II PV
, refer to
the online user manual.
Troubleshooting
My display is not showing any information
This could be because your display is out of range and is not
communicating with the transmitter / meter.
The signal strength to the transmitter is shown on the top left
of the display. The more bars shown, the better the signal and
performance of the display.
Try moving your display closer to the transmitter and meter. If
problems persist, please refer to our website.
My display is blank or has switched itself off
The display backlight may have turned itself off if configured to
do so. Press any button on the display to switch it back on.
The backlight can be set to switch off between certain hours of
the day. To make a change to this setting, enter the
[ADVANCED]
settings and change
DISPLAY OFF
and
DISPLAY ON
to your
requirements.
If the display remains off even after pressing a button, check
the power supply connection and then refer to our website if
the problem persists.
Safety notice
It is important to observe some simple safety precautions
when using this product. Safe operation of your
Solo II PV
is impaired if used in a manner not specified by the
manufacturer.
j
Keep the
Solo II PV
away from water and other
liquids. Disconnect from the mains power supply
before cleaning (with a soft, dry cloth only). Please
contact your supplier if any components appear
damaged or faulty.
l
Your
Solo II PV
is designed to be used in an indoor,
domestic environment only.
n
To protect the environment, this product and its
batteries must be disposed of safely at the end of its
life.
o
This product is CE approved.
m
This product complies with RoHS regulations.
Further information
This guide is designed to introduce you to the
Solo II PV
. In it
you’ll find some basic information about the key features and
functionality.
User manual
A full online user manual is available at
http://www.greenenergyoptions.co.uk/solo2
Technical specifications
Solo II PV display
This product is intended to be used indoors in a domestic
environment. It is not suitable for outdoor use.
Display model
Solo II PV / PCK-S2-011
Supply voltage
240Vac, 50Hz
Operating voltage
5Vdc
Operating power
< 0.6W
Operating temperature
0 to 40ºC
Operating humidity
0 to 85% non-condensing
Manufacturer
Green Energy Options Ltd.
3 St. Mary’s Court, Main Street, Hardwick, Cambridge
CB23 7QS, UK
This unit has been tested and conforms to the following
standards:
Health & Safety (Article 3.1a)
EN 60950-1:2005 (2
nd
edition), Am 1:2009 *
EMC (Article 3.1b)
EN 301 489-3 V1.4,1
EN 301 489-1 V1.8.1
EN 5502:2006 / A1:2007 (Class B) *
EN 61000-3-2:2006 *
EN 61000-3-3:2008 *
EN 55024:1998 / A1:2001 / A2:2003 *
Spectrum (Article 3.2)
EN 300 220-2 V2.3.1
* Denotes specific standards for the power supply
SOL2-A-QSG-006_1
Solo II PV
QUICK START GUIDE
SOL2-A-QSG-006_1.indd 1
18/11/2014 10:10