Generex CS121BL User Manual Download Page 18 | Manualshive

Page: 18 / 166

background image

16

3.3

Setup of the Basic Network Configuration

Note:

We recommend the following settings for the operation of the CS121 via

cross cable (Ethernet cable for the connection directly). Set the IP address of the workstation
with a cross cable to an IP address of the same network segment, e.g. 10.10.10.11 AND set
the gateway to 10.10.10.10.

A network cross cable is a PC-PC network cable, which does not require a switch or a hub
between 2 network workstations (2). Most modern workstation network cards have an auto
detection, so any network cable may be used. Only if you do not have such a cable, connect a
switch or Hub between your workstation and the CS121 (1).

Figure 4:

Connection PC-Switch/Hub and CS121 (2) Connection PC-Cross
Cable/Network Cable and CS121

3.3.1

DHCP

– Obtain an IP address automatically

By default DHCP is off at all CS121. From CS121 FirmWare Version 4.25.x you can switch on
DHCP via DIP switch 2 manually. Therefore the CS121 will get a DHCP IP address from the
DHCP server during reboot. Prior of that, you should detect the MAC address of the CS121 to
be able to find the IP address on your DHCP server. You can also use the GENEREX
Netfinder tool (

http://www.generex.de/generex/download/software/install/NetFinder.zip

). This

tool searches all CS121/BACS devices into your network environment.

We recommend to use

static IP addresses, because the CS121 is used for multi server shutdowns via RCCMD too
and it might be, that the DHCP server got a breakdown.

For that reason the delivery default of

the CS121 is always with DHCP OFF!

Note:

The  function  DHCP  ON/OFF  is  valid  for  the  following  models  only:  all
CS121  HW  131  and  all  BACS  II  Webmanager  Budget  (not  valid  for  all
CS121  HW  121,  SiteManager,  SiteMonitor,  MiniSlot,  CS121_RII  and
Piller I/O Board)!

3.3.2

Establishment of a static CS121 IP address manually (default delivery state)

The minimum requirement to operate the SNMP-adapter is to set the IP address, subnet mask
and the UPS model:

The DIP-switches of the SNMP-adapter firstly need to be set for the configuration. DIP-

switch 1 is switched OFF in the top position as well as DIP switch 2 is switched OFF.

Note:

For  slot  versions  you  have  to  insert  and  remove  the  device  for  any
reboot-process.  This  will  not  have  any  effect  on  your  UPS  but  we
recommend  doing such  operations  only  when  the  UPS  is  not supplying
any load!

«
...
16
17
18
19
20
...
»

Summary of Contents for CS121BL







































































































































































Reviews:

No comments

Related manuals for CS121BL

Brand: Eaton Pages: 166

Brand: Panasonic Pages: 45

Brand: Panasonic Pages: 3

Brand: BEIER-Electronic Pages: 22

Brand: Samsung Pages: 16

Brand: Barthelme Pages: 8

Brand: CAB Pages: 28

Brand: C-TEC Pages: 16

Brand: C&T Solution Pages: 27

SECURIT ST800L+

Brand: C&K systems Pages: 16

Brand: National Instruments Pages: 29

Brand: Lamtec Pages: 22

M16/RM N.C. DN 65 EEX

Brand: Madas Pages: 44

Brand: Pando Pages: 43

Brand: V2 Pages: 12

NORA-W10 Series

Brand: u-blox Pages: 56

Brand: z21 Pages: 2

traxon e:cue LCE-mx

Brand: Osram Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands