General Monitors S4000C Instruction Manual Download Page 53 | Manualshive

Page: 53 / 54

background image

S4000C

43

9.7 FMRC Approval

Factory Mutual Research Corporation

1151 Boston-Providence Turnpike

Norwood, Massachusetts 02062

Approval of the transmitter does not include, or imply, approval of apparatus to which the
transmitter may be connected and which processes the electronic signal for the eventual end
use. In order to maintain FMRC approved system, the control instrument, to which the subject
instrument is connected, must be FMRC approved.

The following sensors have been FMRC approved for use with the Model S4000C:

•

10001-1 Aluminum Body General Purpose Combustible Gas Sensor

•

10058-1 Stainless Steel Body General Purpose Combustible Gas Sensor

The following apparatus have been FMRC approved (although they have not been verified as
part of a Model S4000C system):

•

Model DC110 Eight Channel Readout/Relay Display Module

•

Model DC130 Dual Channel Readout/Relay Display Module

Factory Mutual Research Corporation has tested the Model S4000C according to the criteria
listed under the FMRC Approval Standards for Combustible Gas Detectors, Class Numbers
6310 & 6320.

FMRC has tested the Model S4000C using the specifications listed in Section 9.2. This permits
an operating temperature of -40°F to +167°F (-40°C to +75°C), a general purpose sensor
(10001-1 or 10058-1) attached to the housing (i.e. not remote), calibration performed with a
General Monitors’ Portable Purge Calibrator using 50% LEL gas (Methane, Hydrogen,
Butadiene, Butane, Ethane or Propane) and the procedure listed in Section 4.5. The conduit
containing wires connected to the relay contacts must be sealed. If the non-latching relay
option has been selected from the relay options, the user must provide alternate means of
latching the relay output.

«
...
51
52
53
54
»

Summary of Contents for S4000C























































Reviews:

No comments

Related manuals for S4000C

Brand: Y-cam Pages: 12

Brand: CAME Pages: 2

Brand: N-Com Pages: 28

Brand: Jeep Pages: 7

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: Patton electronics Pages: 8

Brand: Harbor Freight Tools Pages: 4

Brand: Kargo Master Pages: 13

Brand: Kargo Master Pages: 21

Brand: Kargo Master Pages: 4

Brand: Karel Pages: 56

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Pages: 2

Brand: Nautronic Pages: 7

Brand: NAPCO Pages: 16

Brand: Talkswitch Pages: 334

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands