manualshive.com logo in svg

Generac Power Systems MLT6SMD, Owner'S Manual

Share
Download
Generac Power Systems MLT6SMD Owner'S Manual Download Page 11

Introduction and Safety

Owner’s Manual for MLT6SMD Light Tower

7

Reporting Trailer Safety Defects

If you believe your trailer has a defect which could cause
a crash or could cause injury or death, you should imme-
diately inform the National Highway Traffic Safety Admin-
istration (NHTSA) in addition to notifying Generac Mobile
Products, LLC.

If NHTSA receives similar complaints, it may open an
investigation, and if it determines a safety defect exists in
a group of vehicles, it may order a recall and remedy
campaign. However, NHTSA cannot become involved in
an individual problem between you, your dealer, or Gen-
erac Mobile Products, LLC.

To contact NHTSA, you may either call the Auto Safety
Hotline toll-free at 1-888-327-4236 (TTY:1-800-424-9153),
go to 

http://www.safercar.gov

; or write to:

Administrator

NHTSA

1200 New Jersey Avenue S.E.

Washington, DC 20590

You can also obtain other information about motor vehicle
safety from 

http://www.safercar.gov

.

Summary of Contents for MLT6SMD





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands