manualshive.com logo in svg

Gemotech RemoDAQ-8000 Series, User Manual, Page: 10 / 23

Share
Download
Gemotech RemoDAQ-8000 Series User Manual Download Page 10

RemoDAQ-8054 User’s Manual 

RemoDAQ converter module, a personal computer with RS- 
232 port (baudrate set to 9600) and theRemoDAQ utility software. 

Configuration with the RemoDAQ Utility Software 

The easiest way to configure the RemoDAQ module is by 

using the RemoDAQ utility software

：

an easy-to-use menu- 

structured program will guide you through every step of the 
configuration. 

Configuration with the

 

RemoDAQ command set 

RemoDAQ modules can also be configured by issuing 

direct commands from within a terminal emulation program 
that is part of the RemoDAQ utility software. 

The following example guides you through the setup of an 

analog input module. Assume that RemoDAQ-8054 still has 
its default settings (baud rate 9600 and address 01h). Before 
the module is reconfigured, it is first requested to send its 
default settings. 

To change the configuration setting of the analog input 

module, the following command is issued

：

 

%0107400600(cr) 

% = change configuration 
01 = target module at address 00 to

：

 

07 = change address to 07 hexadecimal 
40 = set input range to Type 40   
06 = set baud rate to 9600 
00 = set integration time to 50 ms (60 Hz) 

disable checksum 
set data format to engineering units 

 

9

Summary of Contents for RemoDAQ-8000 Series
























Reviews:

No comments