3.0 - OPERATING INSTRUCTIONS
USER MANUAL
3.1 - COMPLETE SYSTEM ARMING
3.2 - SYSTEM ARMING WITH SENSORS EXCLUDED
Press the lock button on the vehicle remote control or button
system arming is confirmed by a siren chirp and a flash of the turn indicators.
The system has a 30” pre-arming “neutral time” during which the LED is turned ON steady.
The system can be armed without activating the internal volumetric protection and the external
sensors (wirless infrared or
.
To do so, press button 3 on the Gemini remote control or proceed as follows:
•Insert the electronic key into its receptacle; the LED will give a quick flash.
•Close all doors and press the lock button on the vehicle remote control.
“1” on the Gemini remote control (art.
938);
wireless hyper-frequency)
•System arming is confirmed by the standard audio/visual arming signals.
3.3 - PASSIVE ARMING
If programmed for passive arming, the system will automatically arm approximately 60” after ignition is
switched OFF and the last door is opened and closed.
System arming is confirmed by the standard audio/visual arming signals.
If programmed for passive arming, the system will automatically arm approximately 60”
after ignition is switched OFF and the last door is opened and closed.
System arming is confirmed by the standard audio/visual arming signals.
3.4 - ARMING NEUTRAL TIME
3.5 - SYSTEM ARMED
System neutral arming time lasts 30” and is signaled by the LED being ON steady; during this lapse of
time you can exit the vehicle without triggering any alarm.
After the neutral time, the system is armed and ready to detect theft attempts. The LED will start
flashing when the system is fully armed.
Exclusion of sensors is bound to each single arming cycle.
PAGE 04 - USER MANUAL
3.8 - EMERGENCY DISARMING WITH ELECTRONIC KEY
This disarming procedure is used for “EMERGENCY DISARMING” and “TOTAL DISARMING”.
When the electronic key is inserted in its receptacle, the system disarms and switches OFF.
It will not rearm by pressing the lock button on the vehicle remote control or the GEMINI remote
control.
USER MANUAL - PAGE 05
3.7 - SYSTEM DISARMING
Press the unlock button on the vehicle original remote or button
flashes of the turn indicators.
If, when the system is disarmed, the siren chirps 5 times and the turn indicators flash 5 times, it means
that there has been a theft attempt.
Paragraph 3.9 details all possible alarm causes and relative signals.
“2” on the Gemini remote (art. 938);
system disarming is confirmed by 2 siren chirps and by 2
For safety reasons, during an alarm event, the system cannot be disarmed via the
Gemini remote control (art.938) but only with the vehicle original remote control.
To restore normal operation, insert the electronic key in its receptacle.
A quick siren chirp and a quick flash of the status LED will confirm that the system is
back to normal mode.
3.9 - ALARM MEMORY
The LED memory allows to determine what generated the last alarm (indicated by the 5 siren chirps
and the 5 turn indicator flashes triggered when the system was disarmed).
Turn ignition key “ON”. The LED will start to blink according to the last alarm detected (see table
below).
The flash sequence is repeated 3 times; to interrupt simply turn ignition key “OFF”.
LED FLASHES
ALARM CAUSES
ALARM
CYCLES
10
10
1
1
0
10
0
10
10
10
Ignition attempt (+15/54)
Boot opening
Volumetric or external sensor
Wireless magnetic contacts or
opening detectors
Wireless infrared sensors (PIR) or
wireless hyper-frequency sensors
Wire tampering
Door opening
Bonnet opening
LED ON (1 second)
LED OFF (2 seconds)
3.6 - ALARM, NEUTRAL TIME BETWEEN ALARMS AND ALARM CYCLES
Theft attempts are signaled by audio/visual signals.
Once the alarm ceases, there is a 5” time-interval before another alarm can be triggered.
Each alarm event can generate up to 10 cycles of 30” each, for each input and for each arming cycle
Exclusion via remote control is only available for the following vehicles:
• FIAT DUCATO ‘11
• FORD TRANSIT ‘14
• RENAULT MASTER ‘10
›
›
›
For the following alarm systems, the above sensors can be excluded via remote control:
•
•
Proceed as follows:
• Lock the vehicle via the vehicle original remote control.
• Wait at least 5 sec. (but before the end of the arming neutral time); press the lock button again.
• Exclusion is confirmed by 1 acoustic low tone signal (Bop).
THE CONFIRMATION TONE CANNOT BE EXCLUDED.
933MHD and 933MHR starting from revision Rev.06 (see barcode label).
933MHT starting from revision Rev.01 (see barcode label).
NB:
