manualshive.com logo in svg

Gemalto SafeNet ProtectServer, Installation And Configuration Manual, Page: 13 / 44

Share
Download
Gemalto SafeNet ProtectServer Installation And Configuration Manual Download Page 13

 

7 

Chapter 4

 

 

Installation 

This chapter provides information on how to install the SafeNet ProtectServer 
Network HSM. 

Since the SafeNet ProtectServer Network HSM is delivered with the necessary 
software components pre-installed, no software installation is necessary on the unit 
itself. 

Once installation is complete, the unit can be tested to confirm correct operation and 
to configure the network settings. These steps are covered in "Testing and 
configuration" on page 9. 

Installation procedure 

To install the hardware 

1.

 

Choose a suitable location to site the equipment. You can mount the SafeNet ProtectServer 

Network HSM in a standard 19-inch rack, as described in the Quickstart Guide. 

Note: 

The plug in the power supply cord is the disconnect device for this equipment. 
The equipment must therefore be installed near to the mains outlet socket to which 
it is connected and the mains outlet socket must be easily accessible. 

2.

 

Connect the SafeNet ProtectServer Network HSM to the network that hosts the client 

machine(s) where the SafeNet cryptographic API software is installed. Connect the SafeNet 
ProtectServer Network HSM to the network by inserting standard Ethernet cables into the LAN 
connectors located on the front of the SafeNet ProtectServer Network HSM. The LAN connectors 
are autosensing 10/100/1000 Mb/s Ethernet RJ45 ports. 

Note: 

The SafeNet ProtectServer Network HSM is equipped with two NICs (

eth0

 and 

eth1

), each of which can be configured with its own IP address. The NICs 

incorporate an IPv4/IPv6 dual stack, allowing you to configure both an Ipv4 and 
IPv6 address on each interface. If you intend to use both NICs, connect Ethernet 
cables to both LAN connectors. 

3.

 

Connect the power cable to the unit and a suitable power source. The SafeNet ProtectServer 

Network HSM is equipped with an autosensing power supply that can accept 100-240V at 50-
60Hz. 

Smart Card Reader Installation 

The ProtectServer offers functionality supporting the use of smart cards. To make use 
of these features, you must use a SafeNet-supplied smart card reader. Smart card 
readers, other than those supplied by SafeNet, are not supported. 

The SafeNet ProtectServer Network HSM supports two different card readers, as 
follows: 

 

the new USB card reader (introduced in 5.2) 

Summary of Contents for SafeNet ProtectServer













































Reviews:

No comments