manualshive.com logo in svg

Gemalto Cinterion EMS31-V, Hardware Interface Overview

Share
Download
Gemalto Cinterion EMS31-V Hardware Interface Overview Download Page 13

Cinterion

®

 EMS31-V Hardware Interface Overview

2.1 Application Interface

18

EMS31_V_HIO_v00.004

2018-02-27

Confidential / Preliminary

Page 13 of 35

2.1.4

GPIO Interface

EMS31-V offers a GPIO interface with 20 GPIO lines. The lines are shared with other interfaces
or functions: ASC0 (see 

Section 2.1.1

), ASC1 (see 

Section 2.1.2

), status LED (see 

Section

2.1.5.1

), Fast shutdown (see 

Section 2.1.5.2

), 

The following table shows the configuration variants for the GPIO pads. All variants are mutu-
ally exclusive, i.e. a pad configured for instance as ASC0 is locked for alternative usage.

*) Note: The following features are not yet available with the current product release: GPIO, I

2

C, Pulse

Counter, PWM and SPI.

After startup, the above mentioned alternative GPIO line assignments can be configured using
AT commands (see 

[1]

). The configuration is non-volatile and available after module restart.

Table 2:  

GPIO lines and possible alternative assignment

GPIO*

Fast 
Shut-
down

Status 
LED

Pulse 
Counter*

ASC0

ASC1

SPI*

PWM*

WAKE
capability

GPIO1

DTR0

Available

GPIO2

DCD0

GPIO3

DSR0

GPIO4

FST_SHD

N

GPIO5

LED

GPIO6

PWM2

GPIO7

PWM1

GPIO8

COUNTER

Available

GPIO16

RXD1

GPIO17

TXD1

GPIO18

RTS1

Available

GPIO19

CTS1

GPIO20

GPIO21

GPIO22

GPIO23

GPIO24

RING0

Available

GPIO25

Available

GPIO26

SPI_CS

1

GPIO27

SPI_CS

2

n/a

RST0

Available

Summary of Contents for Cinterion EMS31-V




































Reviews:

No comments

Brands by name

Popular brands

Load more brands