background image

 

Rev. 00  03/19 

 

OptiFlex Pro B Spray 

Product description  

  21 

Environmental conditions 

 

OptiFlex Pro B Spray 

 

Utilization 

in the interior 

Height 

up to 2 000 m 

Temperature range 

+5 °C - +40 °C 

(+41 °F - +104 °F) 

Max. surface temperature 

+85 °C (+185 °F) 

Maximum relative humidity  

80 % for temperatures to 31 °C, 

linearly decreasing to 50 % 

relative humidity at 40 °C 

Environment 

not for wet environment 

Degree of pollution of the 

intended environment 

2 (in accordance with DIN EN 

61010-1) 

 

 

Sound pressure level 

 

OptiFlex Pro B Spray 

 

Normal operation  

< 60 dB(A) 

The sound pressure level was measured while the unit was in operation; 

measurements were taken at the most frequent operator positions and at 

a height of 1.7 m from the ground. 
The specified value is applicable only for this product itself and does not 

take into account external noise sources or cleaning impulses. 
The sound pressure level may vary, depending on the product 

configuration and space constraints. 

 

Rating plate 

 

 

fig. 4 

 

 

 

Summary of Contents for OptiFlex Pro B Spray



























































Reviews: