Gefen EXT-UHD600-41 User Manual Download Page 59

Page: 59 / 136

page | 49

RS-232 Configuration

Configure...

Selected the desired COM port.

Configure the RS-232 port to the following settings. Note that

Only TxD, RxD,

and GND pins are used.

Description

Setting

Baud rate

19200

Data bits

Parity

None

Stop bits

Hardware flow control

None

Connect the RS-232 cable from the DB9 connector on the controller to the to the

RS-232 port on the switcher.

5. Type

#help

for a list of commands or refer to the tables on the following pages.

Using Telnet, UDP, and RS-232

DA-15

DE-9

DB-25

DC-37

DD-50

DCD

RXD
TXD

DTR

GND
DSR
RTS
CTS

DCD

RXD
TXD

DTR

GND
DSR
RTS
CTS

1
2
3
4
5
6
7
8
9

RS-232 Controller

Switcher

Summary of Contents for EXT-UHD600-41









































































































































Search results

Summary of Contents for EXT-UHD600-41

Reviews:

Related manuals for EXT-UHD600-41

Brands by name

Popular brands

Gefen EXT-UHD600-41, User Manual

Search results

Summary of Contents for EXT-UHD600-41

Reviews:

Related manuals for EXT-UHD600-41

Brands by name

Popular brands