Gefen EXT-UHD600-41 User Manual Download Page 31

Page: 31 / 136

page | 21

asic Oper

ation

asic Oper

ation

The Web Interface

HPD Control

A Hot-Plug Detect (HPD) is a +5V signal that is sent from the source to the sink, once it is

connected using an HDMI cable. After receiving the signal, the sink device sends a +5V

HPD signal back to the source. HPD is used to begin communication between source and

sink. Within the web interface, an HPD pulse can manually be sent to the source device

from the selected input.

1. Click the

Setup

tab within the built-in web interface.

2. Click the

HPD Control

sub-tab.

3. Click the

Pulse

button for the desired input. Click the

Pulse All Inputs

button to send

an HPD signal from all inputs.

Summary of Contents for EXT-UHD600-41









































































































































Search results

Summary of Contents for EXT-UHD600-41

Reviews:

Related manuals for EXT-UHD600-41

Brands by name

Popular brands

Gefen EXT-UHD600-41, User Manual

Search results

Summary of Contents for EXT-UHD600-41

Reviews:

Related manuals for EXT-UHD600-41

Brands by name

Popular brands