manualshive.com logo in svg

Geeetech A20T, User Manual, Page: 28 / 54

Share
Download
Geeetech A20T User Manual Download Page 28

 

28 

 

SHENZHEN GETECH TECHNOLOGY CO., LTD 

 

(Picture 7-25) 

When the motors are unlocked, you can move them by hand. 

8 Software setting 

8.1 Install driver 

Two printing choices for A20T: TF card printing and USB printing. 

TF card printing: 

After leveling, insert the TF card into the slot, and choose a .gcode file to start

 

printing. 

USB  printing: 

Connect  the  printer  and  computer  with  a  USB  cable  to  control  the  printer

 

with 

slicing  software  such  as  Repetier-Host.  Because  of  some  unstable  factors  such  as  signal 
interference, the USB printing prone to fail. So we suggest choosing TF card printing. 
The details of USB printing are as follows: 
Firstly, turn on the printer, and connect the printer to computer with a USB cable. Normally, the 
computer will automatically search the install driver. The newest communication chip of A20T is 
CH340. See picture (8-1). 

 

(Picture 8-1) 

If it fails to automatically install the driver in computer, then check whether the driver is installed 

Summary of Contents for A20T























































Reviews:

No comments