background image

13

   

   

Safety

Instructions for the Safe Operation

Commissioning/Setup Mode

For commissioning, the following principles apply:

Take protective measures against dangerous contact voltages in accor-
dance with pertinent regulations.

The cleaner must be completely assembled and correctly adjusted. All 
screw connections must be securely tightened. All electrical cables must 
be installed correctly.

Reliably secure machine parts which have already been connected 
against inadvertently being switched on.

Relubricate all lubricating points.

Make sure lubricants are used properly.

After conversion of the cleaner, residual risks must be reassessed.

Setting into Operation

For setting into operation, the following principles apply:

Only allow properly qualified staff to set the cleaner into operation.

Establish all connections correctly.

The safety devices for the cleaner must be complete, fully functional and 
in perfect condition. Check the function before starting any work.

When the cleaner is switched on, the danger zones must be free.

Remove any liquids that have escaped without leaving residues.

Operation

For operation, the following principles apply.

Monitor the cleaner during the operation.

Safety devices must not be changed, removed or taken out of service. 
Check all safety devices at regular intervals.

All guards and hoods must be fitted as intended.

The place of installation of the cleaner must be adequately ventilated at 
all times.

Structural alterations of the cleaner are not permitted. Immediately report 
any changes on the cleaner to the person responsible.

Always keep danger zones clear. Do not leave any objects in the danger 
zone. Only allow persons to enter the danger zone when the machine is 
de-energized.

Regularly check that all emergency stop devices are working correctly.

Summary of Contents for TMC 45







































Reviews: