GEA Omni Instruction Manual Download | Manualshive

Page: 80 / 238

background image

2.12.3

Activity Log Tab

This tab is used to display a log of all events and auditing information for the panel. It is also used to monitor the
network status of the panel.

fig.83:

Activity log tab display

1.

General Log

This table displays the date and details of any user activity logged in the panel. It also records which
user was logged in when each entry was recorded. The data to be displayed is selected through the
fields in the upper right corner of the screen. The lower two fields are used to select a date range to dis-
play. The upper field contains a drop down list which is used to select the type of data to be displayed.
The options are displayed below:

•

All Data

•

Parameter Changed

•

Configuration Changed

•

Settings Changed

•

Commands

•

File Handling

•

Power

•

Network

•

Error Log
This option is only available for a user with service level or higher permissions.

User interface
Service

Instruction Manual | GEA Omni™

Control panel

80

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
78
79
80
81
82
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: C.Nord Pages: 100

CoreBuilder 9000

Brand: 3Com Pages: 78

Brand: GAUGEMASTER Pages: 2

Brand: EasyIO Pages: 19

Brand: Zero 88 Pages: 2

Brand: Zenit Pages: 24

Brand: IDK Pages: 96

Brand: Eaton Pages: 2

Gemini GEM-P9600

Brand: NAPCO Pages: 6

Gemini GEM-P816

Brand: NAPCO Pages: 56

Brand: National Instruments Pages: 102

Brand: NAU ROBOTICS Pages: 109

Maschine Mikro MK2

Brand: Native Instruments Pages: 181

Brand: WAREMA Pages: 112

Brand: WAGO Pages: 414

Brand: V2 Pages: 48

Brand: hager Pages: 4

Brand: FUTABA Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands