GEA Omni Page 220 Instruction Manual Download

Page: 220 / 238

4.2.3

List and Description of Condenser Warnings

Warning

Explanation

Condenser Loss Of Interlock

This annunciation will be triggered if a condenser device is instructed to run
by the sequencing schedule but the run status is not energized.

Condenser High Discharge
Pressure

This annunciation will be triggered if the Condenser Discharge Pressure
exceeds the

Condenser High Discharge Pressure Warning

parameter for the

period of time defined by the

High Discharge Pressure Warning Delay

parameter.

Condenser Low Discharge
Pressure

This annunciation will be triggered if the Condenser Discharge Pressure falls
below the

Condenser Low Discharge Pressure Warning

parameter for the

period of time defined by the

Low Discharge Pressure Warning Delay

param-

eter.

4.2.4

List and Description of Evaporator Warnings

Warning

Explanation

Evaporator Max Liquid Level

This annunciation will be triggered if a high liquid level is detected. This
annunciation is only for GEA BluAstrum.

High Temperature

This annunciation will be triggered if the temperature measured by an evapo-
rator temperature probe exceeds the value of the zone’s

High Temperature

Warning Set Point

for a period of time defined by the corresponding

Low

Temperature Warning Delay

parameter.

Low Temperature

This annunciation will be triggered if the temperature measured by an evapo-
rator temperature probe falls below the value of the zone’s

Low Temperature

Warning Set Point

for a period of time defined by the corresponding

Low

Temperature Warning Delay

parameter.

Secondary Refrigerant Feed-
back Pump

This annunciation will be triggered if the run feedback module for the secon-
dary refrigerant pump is de-energized while the pump is instructed to run.

Secondary Refrigerant Feed-
back Flow

This annunciation will be triggered if no flow is detected while the secondary
refrigerant pump is running.

Annunciations
Warnings

Instruction Manual | GEA Omni™

Control panel

220

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

Summary of Contents for Omni















































































































































































































































Search results

Summary of Contents for Omni

Reviews:

Related manuals for Omni

Brands by name

Popular brands

GEA Omni, Instruction Manual

Search results

Summary of Contents for Omni

Reviews:

Related manuals for Omni

Brands by name

Popular brands