GEA Omni Instruction Manual Download | Manualshive

Page: 206 / 238

background image

3.13.4

No Pump

This option is selected if the compressor is not equipped with an external oil pump. In this situation, the oil pres-
sure differential is maintained by the compressor.

3.14

IntelliSOC

An electronic modulating valve is provided to control the oil cooling. The position of the valve is based on the
discharge or oil temperature. The desired temperature is an operator-adjustable parameter. The modulating
valve is held closed for two seconds after the shutoff solenoid is energized to allow pressure to build against the
control valve.
The modulating valve will calibrate itself every time the compressor is successfully stopped from the running
state. While calibrating, the valve will be set to 4mA and fully close to its 0% position. It will remain in this state
for a period of time as defined in the

Calibrate Time Before Bleed

parameter. Following the delay, the valve will

remain at its minimum position until the compressor is started. At its minimum position, the valve is permitted to
open slightly to prevent liquid from becoming trapped between the valve and the shutoff solenoid.

Control
IntelliSOC

Instruction Manual | GEA Omni™

Control panel

206

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
204
205
206
207
208
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: ABB Pages: 2

Brand: QCON Pages: 4

Brand: DayTronic Pages: 22

Brand: DayTronic Pages: 414

Brand: Fantech Pages: 2

Brand: U.S. Divers Pages: 22

Brand: UniPOS Pages: 51

Brand: Unipulse Pages: 126

Brand: YachtSafe Pages: 3

Brand: Linak Pages: 33

LMT070DICFWD-NJN

Brand: Topway Pages: 34

Brand: Rain Bird Pages: 48

Brand: Sullair Pages: 31

Brand: Carel Pages: 48

Controller CR100

Brand: Sonos Pages: 12

Brand: ADLINK Technology Pages: 37

Samos Pro Compact SP-COP2

Brand: Wieland Pages: 36

CONPAL NCB-8C-SR

Brand: Nabtesco Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands