GEA Omni Instruction Manual Download | Manualshive

Page: 178 / 238

background image

Value

Description

Volume Slide Position

This value displays the current reading of the volume slide position sensor. The
value is measured in percent. This point may monitor either a 4-20 mA signal or a
potentiometer input.

Primary Slide Position or
Swept Volume in %

This value displays the current reading of the primary slide position or swept vol-
ume. It is used for applications were an analog output module is provided to
retransmit the current reading of the primary slide position sensor. The value is
measured in percent. The default location for the module is dependent on where
the panel was configured.

Motor Current

This value displays the current reading of the compressor motor current sensor.
The value is measured in Amps. It will not appear on a slice if Motor Starter Com-
munication is enabled in the configuration. This point may monitor either a 4-20
mA signal or a current transformer input.

3.7.2

Standard Calculated Values

Hint!

These entries in the operating data table are not tied to a default position in the I/O system.
They are calculated by the system.

Value

Description

Loop time

This value represents the amount of time the system requires to execute all cus-
tom logic once and update all inputs and outputs. The value is measured in sec-
onds.

Oil Filter Differential

This value displays the calculated differential in the oil filter. The calculation used
is dependent on the compressor’s configuration. The value is measured in the cur-
rent pressure units of the panel.

Oil Differential

This value displays the calculated oil differential in the compressor. The calculation
used is dependent on the compressor’s configuration. The value is measured in
the current pressure units of the panel.

Motor Current

This value displays the value of the motor current as read through the motor
starter communication. It will not be visible if Motor Starter communication has not
been enabled in the configuration. The value is measured in Amps.

Cycle On Timer

This value displays the remaining time before the compressor will restart automati-
cally. It will only be visible if Automatic Start/Stop is enabled in the configuration.
The value is measured in seconds.

Control
Compressor Operating Data

Instruction Manual | GEA Omni™

Control panel

178

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
176
177
178
179
180
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

ControlMaster CM15

Brand: ABB Pages: 28

Brand: Lawler Pages: 4

Brand: hager Pages: 62

coviva Smartbox TKP100A

Brand: hager Pages: 45

Brand: Kamstrup Pages: 36

Brand: JFA Electronicos Pages: 29

Brand: Rachio Pages: 2

Brand: Kärcher Pages: 4

Brand: UniPOS Pages: 51

Brand: Unipulse Pages: 126

Brand: YachtSafe Pages: 3

Brand: Audioaccess Pages: 2

Brand: Black Horse Model Pages: 19

Brand: Belimo Pages: 9

Brand: SMC Networks Pages: 31

VEGACAP 60 Series

Brand: Vega Pages: 12

Brand: D+H Pages: 17

Brand: Nordson Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands