GEA Omni Instruction Manual Download | Manualshive

Page: 177 / 238

background image

3.7.1

Analog Inputs/ Outputs

Hint!

The assignment of the data points is dependent on the configuration. Check the electrical con-
nection diagram to identify the exact layout of the data points.

Value

Description

Suction Pressure

This value displays the reading of the suction pressure transducer. The value is
displayed in the current pressure units of the panel.

Discharge Pressure

This value displays the reading of the discharge pressure transducer. The value is
displayed in the current pressure units of the panel.

Oil Pressure

This value displays the reading of the oil pressure transducer. The value is dis-
played in the current pressure units of the panel.

Oil Filter Pressure

This value displays the reading of the oil filter pressure transducer. This point will
only be displayed if the oil filter is configured with a single pressure transducer.
Depending on configuration options, this may be either an input or output trans-
ducer.

Oil Filter Inlet Pressure

This value displays the reading of the oil filter pressure transducer. This point will
only be displayed if the oil filter is configured with both an input and output trans-
ducer. The value is displayed in the current pressure units of the panel.

Oil Filter Outlet Pressure

This value displays the reading of the pressure transducer located at the oil filter
outlet valve. This point will only be displayed if the oil filter is configured with both
an input and output transducer. The value is displayed in the current pressure
units of the panel.

Suction Temperature

This value displays the reading of the suction temperature sensor. The value is
displayed in the current temperature units of the panel.

Discharge Temperature

This value displays the reading of the discharge temperature sensor. The value is
displayed in the current temperature units of the panel.

Oil Temperature

This value displays the reading of the oil temperature sensor. The value is dis-
played in the current temperature units of the panel.

Oil Separator Tempera-
ture

This value displays the reading of the oil separator temperature sensor. The value
is displayed in the current temperature units of the panel.

Capacity Slide Position

This value displays the current reading of the capacity slide position sensor. The
value is displayed in percent. This point may monitor either a 4-20 mA signal or a
potentiometer input.

Instruction Manual | GEA Omni™
Control panel

Control

Compressor Operating Data

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

177

«
...
175
176
177
178
179
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: Gardena Pages: 100

Brand: IBM Pages: 72

Brand: Waterway Pages: 16

Brand: Unitech Pages: 11

Brand: B meters Pages: 10

EtherNetIP ControlPlex CPC12EN

Brand: E-T-A Pages: 28

Brand: Gardner Denver Pages: 22

Brand: B&G Pages: 2

Brand: Hanna Instruments Pages: 88

Brand: M-system Pages: 103

Brand: M-system Pages: 18

Brand: M-system Pages: 7

Brand: Balboa Pages: 74

Brand: Cadac Pages: 4

disklavier DKC-850

Brand: Yamaha Pages: 2

Brand: Frico Pages: 12

Brand: Elotech Pages: 20

Brand: Intermatic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands