manualshive.com logo in svg

GEA Omni, Instruction Manual

Introducing the Instant Omni - your ultimate kitchen companion! Achieve culinary excellence effortlessly with its innovative features and user-friendly interface. Unlock the full potential of your Instant Omni by accessing the comprehensive User Manual for free. Download it now from manualshive.com, and master your culinary skills with ease.

Share
Download
background image

4.

Refrigerant Sensor High High Warning Enabled

This parameter is used to select whether the sensor is configured to annunciate a high high refrigerant warn-
ing condition. The options are:

•

Enabled

•

Disabled

5.

Refrigerant Sensor High High Warning

This parameter is used to select the refrigerant level above which a high high refrigerant warning condition
will be triggered. It will only appear if the 

Refrigerant Sensor High High Warning

 parameter is set to 

Enabled

.

The value is measured in parts per million.

Hint!

The minimum and maximum values of this parameter vary based on the values of the High
Warning and High High Shutdown parameters. The minimum vale of this parameter will be
equal to the current value of the high warning parameter, and the maximum value will be equal
to the current value of the high high shutdown parameter.

6.

Refrigerant Sensor High High Warning Delay

This parameter is used to select the period of time for which a high high refrigerant warning condition must
persist before an annunciation will be triggered. It will only appear if the 

Refrigerant Sensor High High Warn-

ing

 parameter is set to 

Enabled

. The value is measured in seconds.

7.

Refrigerant Sensor High High Shutdown Enabled

This parameter is used to select whether the sensor is configured to annunciate a high high refrigerant shut-
down condition. The options are:

•

Enabled

•

Disabled

8.

Refrigerant Sensor High High Shutdown

This parameter is used to select the refrigerant level above which a high high refrigerant shutdown condition
will be triggered. It will only appear if the 

Refrigerant Sensor High High Shutdown

 parameter is set to 

Ena-

bled

. The value is measured in parts per million.

9.

Refrigerant Sensor High High Shutdown Delay

This parameter is used to select the period of time for which a high high refrigerant shutdown condition must
persist before an annunciation will be triggered. It will only appear if the 

Refrigerant Sensor High High Shut-

down

 parameter is set to 

Enabled

. The value is measured in seconds.

3.7

Compressor Operating Data

Operating Data is displayed on the main Omni 

Compressor

 screen detailed in Section 2.5.1, Page 31. Below is a

list of standard operating variables and a brief description of their functions.

Control
Compressor Operating Data

Instruction Manual | GEA Omni™

Control panel

176

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Waterway OASIS Instruction Manual preview
OASIS
Brand: Waterway Pages: 16
NEC N8403-019 User Manual preview
N8403-019
Brand: NEC Pages: 146
Warren Controls 313 Installation, Operation & Maintenance Instructions Manual preview
313
Brand: Warren Controls Pages: 16
3M PX5 Series Reference Manual preview
PX5 Series
Brand: 3M Pages: 34
Lawler 911 Installation & Maintenance Manual preview
911
Brand: Lawler Pages: 6
Data Aire dap4 touch Supplement Manual preview
dap4 touch
Brand: Data Aire Pages: 28
Racal Instruments 1260 Manual preview
1260
Brand: Racal Instruments Pages: 94
Racal Instruments 1260 User Manual preview
1260
Brand: Racal Instruments Pages: 97
tau K125M Installation Manuals preview
K125M
Brand: tau Pages: 9
tau K100M Translation Of Original Instructions preview
K100M
Brand: tau Pages: 8
iDTRONIC BLEUBOX R-IN-UHF-5239U Manual preview
BLEUBOX R-IN-UHF-5239U
Brand: iDTRONIC Pages: 13
Konig IR-URC30 Manual preview
IR-URC30
Brand: Konig Pages: 8
Gain Electronic SAGA1-K Series Installation & Operation Manual preview
SAGA1-K Series
Brand: Gain Electronic Pages: 17
Vexve Hydrox Series Installation, Operation And Maintenance Manual preview
Hydrox Series
Brand: Vexve Pages: 24
W.E.S.T. Elektronik POS-123-P-PFN Technical Documentation Manual preview
POS-123-P-PFN
Brand: W.E.S.T. Elektronik Pages: 53
Kelly KLS7250H User Manual preview
KLS7250H
Brand: Kelly Pages: 35
One for All SAMSUNG URC-4910 User Manual preview
SAMSUNG URC-4910
Brand: One for All Pages: 76
DIG 410BT Series Instruction Manual preview
410BT Series
Brand: DIG Pages: 16

Brands by name

Popular brands

Load more brands