manualshive.com logo in svg

GEA Omni, Instruction Manual

Introducing the Instant Omni - your ultimate kitchen companion! Achieve culinary excellence effortlessly with its innovative features and user-friendly interface. Unlock the full potential of your Instant Omni by accessing the comprehensive User Manual for free. Download it now from manualshive.com, and master your culinary skills with ease.

Share
Download
background image

3.4.2

Variable Speed Fan/Variable Speed Pump

Hint!

These parameters will only appear if the device in question is variable speed.

Parameter

Units

Minimum

Maximum

Default

Proportional Term

Unitless

0.0

500.0

250.0

Integral Term

s/R

1.0 s/R

250.0 s/R

40.0 s/R

Mode

Selection – See Description

Manual Mode Position

Percent

0.0 %

100.0 %

0.0 %

100.0 %

1.

Proportional Term

This parameter is used to set the proportional gain for PI control of the device. This value is multiplied by the
total error between the actual and desired values. The value is unitless.

2.

Integral Term

This parameter is used to set the rate at which the PI controller will change its integral gain based on the
calculated error over time. The value is measured in samples per Repeat (s/R).

3.

Mode

This parameter is used to select whether the PI controller will vary the output automatically or if it will be
controlled manually through the 

Manual Mode Position

 parameter. The options are 

Auto

 and 

Manual

.

4.

Manual Mode Position

This parameter is used to set the desired output of the PI controller while it is operating in manual mode. The
value is measured in percent.

Hint!

This parameter will only appear if the Mode parameter is set to Manual.

3.4.3

Water cooled condenser

Parameter

Units

Minimum

Maximum

Default

Start Condition

None

0 = None

1 = Compressor controlled

Feedback Condenser Unit Warning
Delay

Seconds

0 s

300 s

0 s

Control
Condenser Device Control Parameters

Instruction Manual | GEA Omni™

Control panel

164

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Haldex PR Installation Manual preview
PR
Brand: Haldex Pages: 8
Eaton SCD24 Installation Manual preview
SCD24
Brand: Eaton Pages: 8
ABB RHDE250 Operating Instruction preview
RHDE250
Brand: ABB Pages: 44
Omega CNI16D Quick Start preview
CNI16D
Brand: Omega Pages: 2
Zmotion ZMC408SCAN Hardware Manual preview
ZMC408SCAN
Brand: Zmotion Pages: 34
Panasonic KX-A16B Quick Start Manual preview
KX-A16B
Brand: Panasonic Pages: 8
DSEGenset DSE8003 MKII Operator'S Manual preview
DSE8003 MKII
Brand: DSEGenset Pages: 74
ITALFARAD RC4 Operating Instructions Manual preview
RC4
Brand: ITALFARAD Pages: 32
Gemini GTL5W Instruction Manual preview
GTL5W
Brand: Gemini Pages: 9
M-system R7EWTU Instruction Manual preview
R7EWTU
Brand: M-system Pages: 18
Mosa EAS 15-806 Use And Maintenance Manual preview
EAS 15-806
Brand: Mosa Pages: 28
iDTRONIC BLEUBOX R-IN-UHF-5239U Manual preview
BLEUBOX R-IN-UHF-5239U
Brand: iDTRONIC Pages: 13
Konig IR-URC30 Manual preview
IR-URC30
Brand: Konig Pages: 8
National Instruments PXI-8232 Installation Manual preview
PXI-8232
Brand: National Instruments Pages: 8
TIE AMBITECH BRAKE-PAK Installation & Setup Instructions preview
AMBITECH BRAKE-PAK
Brand: TIE Pages: 5
adept technology sDIO User Manual preview
sDIO
Brand: adept technology Pages: 96
Maco openDoor User Manual preview
openDoor
Brand: Maco Pages: 40
METRON FD4 Manual preview
FD4
Brand: METRON Pages: 34

Brands by name

Popular brands

Load more brands