GEA Omni Instruction Manual Download

Page: 130 / 238

10.

Low Oil Differential Pressure Warning Timer

This parameter is used to select the period of time for which the

Oil Differential Pressure

may exceed the

calculated value for the

Low Oil Differential Pressure Warning

before a

Low Oil Differential Pressure Warn-

ing

is annunciated. The default value of this parameter is dependent on the compressor manufacturer. This

parameter is fixed on Grasso compressors and will not be visible. The value is measured in seconds.

11.

Low Oil Differential Run Delay

This parameter is used to select for what period of time the

Low Oil Differential

parameters will be ignored

after the compressor is started. The default value of this parameter is dependent on the compressor manu-
facturer. The value is measured in seconds.

3.1.13

Oil Filter Pressure

Parameter

Units

Minimum

Maximum

Default

High Oil Filter Differential Shutdown

barG

0.10 barD

20.00 barD

1.38 barD

barA

PSIG

1.5 PSID

290.1 PSID

20.0 PSID

PSIA

kPaG

10 kPaD

2000 kPaD

138 kPaD

kPaA

MPaG

0.010 MPaD

2.000 MPaD

0.138 MPaD

MPaA

kg/cm²G

1.41 kg/cm2D

20.40 kg/cm2D

1.41 kg/cm2D

kg/cm²A

High Oil Filter Differential Warning
Offset

barG

0.10 barD

5.00 barD

1.03 barD

barA

20.00 barD

1.38 barD

PSIG

1.5 PSID

72.5 PSID

14.9 PSID

PSIA

290.1 PSID

20.0 PSID

kPaG

10 kPaD

500 kPaD

103 kPaD

kPaA

Control
Compressor Control Parameters

Instruction Manual | GEA Omni™

Control panel

130

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

Summary of Contents for Omni















































































































































































































































Search results

Summary of Contents for Omni

Reviews:

Related manuals for Omni

Brands by name

Popular brands

GEA Omni, Instruction Manual

Search results

Summary of Contents for Omni

Reviews:

Related manuals for Omni

Brands by name

Popular brands