GE VR11 Reference Manual Download Page 73

Page: 73 / 118

Table 24: BIOS power up status

Status LED

color

Power-up, still Reset state

Red on

BIOS early init

Blink red 1Hz

BIOS start POST

Blink amber 1Hz

BBIOS POSTA init

Blink green 1 Hz

OS system states

Green on

S0 (running)

green

S1 (sleeping)

amber

S4 (halted)

red

S5 /soft off)

off

System halted or reset

Red on

Reset Button

There is a Reset Button on the front panel. An external Reset button may be
connected between the appropriate IO connector at the rear side and GND.

Speaker

An internal buzzer is implemented on the VR11 except on a VR11 style 8.
An external standard PC compatible speaker may be connected between the
appropriate IO connector at the rear side and +5 V.

GE Intelligent Platforms – VR11, VP11 Hardware Reference Manual, Second Edition

Page 73

Summary of Contents for VR11























































































































Search results

Summary of Contents for VR11

Reviews:

Related manuals for VR11

Brands by name

Popular brands

GE VR11, Reference Manual

Search results

Summary of Contents for VR11

Reviews:

Related manuals for VR11

Brands by name

Popular brands