GE VP11 Reference Manual Download Page 93

Page: 93 / 118

VTM22 Interfaces

This chapter describes all connector pin assignments on the VTM22 transition
module.

IDE Connector (P1800)

The IDE interface is designed as a 40-pin 2.54 mm pitch male connector to fit
directly to one or two external IDE hard drives. The cable length must not
exceed 30 cm. It is recommended to use an 80 pole high density cable for
UDMA transfer.

Table 35: VTM22 IDE connector

Name

P1800

Name

GND

2 1

\RST_DRV

HD_D8

4 3

HD_D7

HD_D9

6 5

HD_D6

HD_D10

8 7

HD_D5

HD_D11

10 9

HD_D4

HD_D12

12 11

HD_D3

HD_D13

14 13

HD_D2

HD_D14

16 15

HD_D1

HD_D15

18 17

HD_D0

NC 20

GND

22 21

HD_DRQ0

GND

24 23

\HD_IOW

GND

26 25

\HD_IOR

NC 28

HD_RDY

GND

30 29

HD_DAK0

32 31

HD_IRQ

34 33

HD_A1

HD_A2

36 35

HD_A0

\HD_CS3

38 37

\HD_CS1

GND

40 39

Ethernet Interface 10/100/1000BaseT (P5000, P5500)

The Ethernet interfaces for RearI/O requires usage of CAT 5 cable for proper
operation with 100/1000BaseT.

GE Intelligent Platforms – VR11, VP11 Hardware Reference Manual, Second Edition

Page 93

Summary of Contents for VP11























































































































Search results

Summary of Contents for VP11

Reviews:

Related manuals for VP11

Brands by name

Popular brands

GE VP11, Reference Manual

Search results

Summary of Contents for VP11

Reviews:

Related manuals for VP11

Brands by name

Popular brands