GE VP11 Reference Manual Download Page 91 | Manualshive

Page: 91 / 118

background image

Appendix A

Transition Module VTM22

The VTM22 transition module is used for easy connection of I/O signals to
standard connectors. Please refer to the drawing for the location of available
interfaces:.

Note:

The +3.3V_SW (pin 6c on P0 = P7300) is switched-on after ramp-up. This is
the only 3.3 VDC source for the Transition Module VTM22. Do not connect
the +3.3V_SW pin to +3.3 V pins; damage may occur.

Please note:

You either can use a DVI display on P4100 or a standard VGA
Monitor/Display connected to P4001 or a standard VGA Monitor/Display via a
DVI-to-VGA adaptor connected to P4100. You never can use two display
devices connected to the transition module. If you want to have two display
outputs, you will have to connect one to the front of the VR11 and one to the
rear transition module.

GE Intelligent Platforms – VR11, VP11 Hardware Reference Manual, Second Edition

Page 91

«
...
89
90
91
92
93
...
»

Summary of Contents for VP11























































































































Reviews:

No comments

Related manuals for VP11

Brand: Biostar Pages: 47

Brand: AKM Pages: 34

Brand: TYAN Pages: 67

Brand: ON Semiconductor Pages: 5

Brand: DIEBOLD NIXDORF Pages: 96

945GC MICRO 775

Brand: Biostar Pages: 49

Brand: NXP Semiconductors Pages: 269

Brand: ASROCK Pages: 160

Venus VNS563-4GD

Brand: Diamond Systems Pages: 43

Brand: AKM Pages: 30

EZ-USB HX2LP CY4606

Brand: Cypress Pages: 2

Brand: Freescale Semiconductor Pages: 16

Brand: JETWAY Pages: 70

Brand: ZMDI Pages: 25

Outboard Motor BF5A

Brand: Honda Pages: 84

Brand: Texas Instruments Pages: 11

Brand: JETWAY Pages: 48

Brand: Broadcom Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands