GE VP11 Reference Manual Download Page 63

Page: 63 / 118

CHAPTER 6

Resources

Chapter Scope

This chapter describes system resources, such as memory mapping, register set
and default interrupt request assignments.

Memory Map

The table below shows the memory address area used by the VR11.

Table 18: Memory map

Address

Size

Used by

$00000 - $9FFFF

640 Kbytes

System RAM

$A0000 - $BFFFF

128 Kbytes

Video RAM (if enabled)

$C0000 - $DFFFF

128 Kbytes

Used by PCI ROMs:
VGA, SCSI, Ethernet

$E0000 - $FFFFF

128 Kbytes

System BIOS

$100000 - $3FFFFFFF

depends on
available DRAM

Extended RAM

$4000000 - $FFFBFFFF

depends on
available DRAM

Dynamically used by
PCI devices

$FEC00000 - $FFEFFFFF

System devices

$FFF00000 - $FFFFFFFF 1 MB Kbytes

System BIOS

Register Set

The following section provides an overview of the registers located in the I/O
address area of the VR11.

GE Intelligent Platforms – VR11, VP11 Hardware Reference Manual, Second Edition

Page 63

Summary of Contents for VP11























































































































Search results

Summary of Contents for VP11

Reviews:

Related manuals for VP11

Brands by name

Popular brands

GE VP11, Reference Manual

Search results

Summary of Contents for VP11

Reviews:

Related manuals for VP11

Brands by name

Popular brands