manualshive.com logo in svg

GE TLE 625 UL S2, User Manual

Share
Download
GE TLE 625 UL S2 User Manual Download Page 70

Critical Power 

 

Modifications reserved 

Page 70/92 

GE_UPS_USM_TLE_SUL_M62_1M0_2US_V010.docx 

User Manual

 TLE Series 625 - 750 - 1000 UL S2

 

 

7.2.2

 

Complete shut-down of the TLE Series 625 - 750 - 1000 as frequency converter 

 

NOTE ! 

Follow this procedure only in case the UPS system and the Load  must be 

completely powered-down. 

 

 

Initial status: 

Load supplied from Inverter

.

 

 

 

 

1.  Perform the command “System shutdown”

. 

Perform the command 

“System shutdown

” through

 

the 

screen: 

Commands 1 / System shutdown / 

Shutdown

 

•

 

Load

 is disconnected from 

UPS.

 

•

 

Rectifier

 and 

Inverter

 are shut-down and all 

contactors

 are 

opened. 

•

 

LED 1 (Rectifier) and LED 2 (Inverter)

 are OFF.

 

•

 

LED ALARM

 is lit. 

 

 

 

2.  Open “Q1 - UPS Output switch” (Pos. O)

. 

 

 

3.  Disconnect the Battery from the UPS by opening the “External Battery Protections”.

 

 

 

 

NOTE ! 

Before performing the next procedure (4) wait 5 

minutes for DC-Link Capacitors discharge. 
Use  the  MEASURES/Rectifier  screen  to ensure 

that the DC-link1 and DC-link 2 voltage has 

reached 10Vdc. 

Press 

“MUTE”

 key to reset 

Acoustical Alarm

. 

LED ALARM

 remains lit. 

 

 

 

4.  Disconnect the Utility from the input distribution

.

 

 

END OF PROCEDURE

 

 

 

 

DANGER ! 

It will take 5 minutes for the DC capacitors to discharge. 
Open only the front door, do not open any other part of the UPS.

 

Summary of Contents for TLE 625 UL S2





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands