GE RTT Instruction Manual Download Page 49

Page: 49 / 94

CHAPTER 2: USING THE RTT ON SR SERIES RELAYS

THE SR735/737 FEEDER PROTECTION RELAY

RTT DESKTOP TEST SET– INSTRUCTION MANUAL

2.5.3

RTT to SR735/737 Wiring Diagram

Ensure that Wet/Dry Input Type switch is set to

DRY

before applying power to the RTT

unit. The SR735/737 Relay accepts only

DRY

contact connections to the RTT.

Ensure that current and voltage knobs are turned fully counter-clockwise before
applying power to the RTT unit.

Note

*The 735/737 Relay doesn’t have Voltage Input, Switch Input and RTD Input features.

**Trip and Aux Common terminals (H5 and H6) must be hardwired together.

Table 2–5: SR735/737 with RTT Set to Dry

RTDs*

RTD3 +

RTD3 -

RTD3 C
RTD2 +

RTD2 -

RTD2 C
RTD1 +

RTD1 -

RTD1 C

SPARE

Contact

Outputs**

AUX COMMON

---------------

RTT

TRIP COMMON

-------------------------

OUTPUT C

AUX NO

-------------------------

OUTPUT 2

TRIP NO

-------------------------

OUTPUT

Contact

Inputs*

INPUT C

INPUT 8
INPUT 7
INPUT 6
INPUT 5
INPUT 4
INPUT 3
INPUT 2
INPUT

CTs

Phase 1 +

-------------------------

Phase 1 COM

-------------------------

VTs*

Summary of Contents for RTT































































































Search results

Summary of Contents for RTT

Reviews:

GE RTT, Instruction Manual, Page: 49 / 94

Search results

Summary of Contents for RTT

Reviews: